How to Turn Off the Tire Pressure Light on a 2016 Honda Accord

You can’t simply “turn off” the tire pressure warning; you must inflate the tires to the door-sticker specification, then perform a TPMS Calibration in the vehicle’s settings, and drive a few miles. If the light stays on or blinks, there may be a system fault that needs diagnosis. Below are the precise steps and troubleshooting tips for the 2016 Accord.

What the Tire Pressure Light Means on a 2016 Accord

The 2016 Honda Accord uses an indirect Tire Pressure Monitoring System (TPMS) that infers pressure changes from wheel-speed data—there are no individual pressure sensors inside the tires. A solid horseshoe-shaped light with an exclamation point usually means at least one tire is low or the system needs recalibration after inflation, rotation, or tire replacement. If the TPMS indicator blinks for about a minute at startup and then stays on, the system has a fault.

Step 1: Check and Set Your Tire Pressures

Before recalibrating, make sure all four tires are inflated to the cold-pressure specification printed on the driver’s door jamb. Pressures drop in cold weather and after time; resetting without correcting pressures will not fix the warning.

1. Park the car for at least 3 hours or check first thing in the morning so tires are “cold.”
2. Find the recommended cold tire pressure on the driver’s door sticker (typical Accords are around 32 psi, but use the exact value on your placard).
3. Use a reliable gauge to measure each tire. Add air to reach the placard pressure; release air if a tire is overinflated.
4. Visually inspect for punctures, embedded objects, sidewall bulges, or bead leaks. Repair or replace any damaged tire before proceeding.

Once all tires match the door-sticker pressure and any damage is addressed, you’re ready to recalibrate the TPMS so the car learns the new “normal.”

Step 2: Calibrate the TPMS (No Physical Reset Button)

Honda requires a manual calibration after inflation, rotation, or tire replacement. The menu path differs slightly depending on whether your Accord has the touchscreen Display Audio or the smaller i-MID screen. Choose the method that matches your car.

If your 2016 Accord has the 7-inch Display Audio touchscreen

Use the on-screen vehicle settings to initialize TPMS calibration.

1. Turn the ignition to ON (engine can be running or in accessory mode).
2. On the touchscreen, tap Home > Settings > Vehicle.
3. Select TPMS Calibration.
4. Tap Calibrate and confirm if prompted.

The system will store the current wheel-speed/pressure baseline and clear the warning after you drive for a short period.

If your 2016 Accord has the i-MID (non-touchscreen) display

Use the steering-wheel controls to reach the vehicle settings and start calibration.

1. Turn the ignition to ON.
2. Press the Menu button on the steering wheel.
3. Select Vehicle Settings (or Customize Settings on some trims) using the up/down arrows; press SEL/RESET.
4. Choose TPMS Calibration (or Initialize TPMS), then select Calibrate; confirm if prompted.

After calibration is initiated, the system needs a short drive to complete learning and turn the light off.

Step 3: Drive to Complete Recalibration

Calibration completes automatically once you drive; this helps the system compare wheel speeds and confirm normal tire behavior.

1. Drive at city or highway speeds (around 25–45 mph or higher) for several minutes.
2. Avoid aggressive cornering during the initial drive so the system can learn a steady baseline.
3. The warning light should turn off as the learning completes; if it stays on, see troubleshooting below.

If you followed the steps and the light turned off, your TPMS has been successfully recalibrated and no further action is needed.

If the Light Won’t Turn Off

Persistent warnings indicate remaining pressure issues or a TPMS/system problem that calibration alone cannot resolve.

• Recheck all four tires with a trusted gauge. A slow leak can drop pressure again within hours.
• Consider temperature effects: a 10°F drop can reduce pressure by about 1 psi. Top off to the placard when cold.
• Confirm tire sizes match front to rear and are OEM-equivalent; mismatched sizes or very uneven wear can confuse the indirect TPMS.
• Look for recent service factors: tire rotation, wheel replacement, suspension or brake work can necessitate another calibration.
• Note the light behavior: if the TPMS indicator blinks for 60–90 seconds and then stays on, there’s likely a system fault (e.g., wheel-speed sensor issue, ABS-related problem, low 12V battery voltage during calibration). Have the vehicle scanned for codes.
• If you recently disconnected or replaced the battery, perform calibration again and drive; if the warning persists, seek diagnostic service.

If checks and recalibration don’t resolve the warning, a technician can scan for fault codes and verify wheel-speed sensor signals, alignment, and software updates.

Tips to Prevent Future TPMS Warnings

Regular attention to tire care reduces nuisance alerts and improves safety, handling, and fuel economy.

• Check pressures monthly and before long trips; adjust when tires are cold.
• Expect seasonal changes; add air as temperatures fall.
• Calibrate TPMS after any tire rotation, replacement, or repair.
• Use matching tire sizes and similar tread depths on all four corners.
• Keep a quality gauge and portable inflator in the car for quick corrections.

Consistent maintenance ensures the TPMS works as intended and minimizes unexpected warnings.

Summary

On a 2016 Honda Accord, you turn off the tire pressure light by first inflating all four tires to the door-sticker specification, then performing TPMS Calibration through the Vehicle settings (either on the Display Audio touchscreen or via the i-MID steering-wheel menu) and driving a few miles. If the light remains on—or blinks and then stays on—recheck pressures, verify tire sizes, and have the system inspected for faults such as wheel-speed sensor or ABS-related issues.

How to make tire pressure light go off on Honda Accord?

To turn off the tire pressure light in a Honda Accord, first reinflate or repair your tires to the correct PSI. Then, power the vehicle on and navigate the infotainment system to Settings > Vehicle > TPMS Calibration > Calibrate, or use the steering wheel buttons to select vehicle settings and TPMS Calibration for models without a touchscreen. Finally, drive for approximately 30 minutes; the light will turn off once the calibration is complete.
 
This video demonstrates how to reset the TPMS light on a Honda Accord with a touchscreen: 53sTommyJacksonTVYouTube · May 4, 2023
Steps to Reset the Tire Pressure Light

1. 1. Check Tire Pressure: Ensure all your tires are inflated to the correct PSI specified on the sticker inside the driver’s side doorjamb. The light will stay on if there is still an underinflated tire. 
2. 2. Power On the Vehicle: With the engine off, turn the ignition to the “on” position by pressing the start button twice without pushing the brake pedal. 
3. 3. Access TPMS Settings: 
   • Touchscreen Models: Select Home on the infotainment system, then navigate to Settings > Vehicle > TPMS Calibration. 
   • Non-Touchscreen Models: Use the steering wheel buttons to go to Driver Information > Vehicle Settings > TPMS Calibration. 
4. 4. Select Calibrate: Choose the Calibrate option to start the reset process. 
5. 5. Drive to Complete Calibration: Drive your Honda Accord for about 30 minutes. The system will automatically complete the calibration process, and the TPMS light will turn off once it is finished. 

If the Light Remains On
If the light is still on after driving, the TPMS may need professional attention. This could indicate a faulty TPMS sensor, which may require a visit to your service center for repair or replacement.

How to manually turn off TPMS light?

Press and hold the TPMS reset button until the tire pressure light blinks three times. Release the button and start the car. The light should go off within 20 minutes. Disconnect the positive battery cable while the vehicle is off.

How to reset low tire pressure light on 2016 Honda Accord?

To reset the TPMS on a 2016 Honda Accord, first check that all tires are filled to the correct PSI. Then, turn the vehicle’s power on (but not necessarily the engine) and navigate to the Settings menu on the infotainment screen or using the steering wheel controls. Select Vehicle Settings > TPMS Calibration > Calibrate. The system will then begin the recalibration process, which finishes automatically while you drive.
 
This video demonstrates how to reset the TPMS using the infotainment system: 55sHondaYouTube · Aug 7, 2023
Step-by-Step Guide

1. 1. Check Tire Pressure: Ensure all four tires (and the spare, if applicable) are inflated to the recommended pressure, which can be found on a sticker on the driver’s side doorjamb. 
2. 2. Turn On Power: With the vehicle parked, press the engine start/stop button twice to turn on the power (ON mode), but without starting the engine. 
3. 3. Access Settings:
   • With Touchscreen: Touch the Home icon on the touchscreen, then select Settings. 
   • Without Touchscreen (Steering Wheel Controls): Press the HOME button on the steering wheel, then use the selector wheel to navigate to and select Settings. 
4. 4. Navigate to TPMS: Select Vehicle Settings, then find and select TPMS Calibration. 
5. 5. Start Calibration: Select Calibrate. A screen indicating that calibration has started should appear. 
6. 6. Drive to Complete: The calibration process will complete automatically after a few miles of driving. 

If the Light Persists:
If the TPMS light stays on or returns, the sensor may be faulty, or there may be a different issue, such as a puncture. In this case, take the vehicle to a mechanic or a dealer for further diagnosis.

Why is my tire pressure light still on after filling tires with Accord?

If you’ve added air but the air pressure warning light stays on, there’s a problem with your Tire Pressure Monitoring System or you have a slow leak… Quick Tip: If the TPMS warning light comes back on after you’ve filled the tire with air, recheck the tire to make sure it is inflated to the proper air pressure.