How much oil does a 2.4 Honda Civic take?

The 2.4-liter Honda Civic—specifically the 2012–2015 Civic Si with the K24Z7 engine—takes about 4.4 U.S. quarts (4.2 liters) of engine oil when the filter is changed, or roughly 4.2 U.S. quarts (4.0 liters) without a filter change. Honda specifies 0W-20 oil for this engine. Below, we explain which models this applies to, how to verify your exact capacity, and best practices for changing and checking the oil.

Which Civic uses the 2.4-liter engine?

Honda only fitted the 2.4L four-cylinder (K24Z7) to the U.S.-market Civic Si from model years 2012 through 2015. If you have a 2012–2015 Civic Si, the capacities in this article apply. Other Civics from that era (e.g., the 1.8L non-Si or earlier 2.0L Si) have different oil capacities.

Official capacity and oil type

For owners performing maintenance or verifying specs, the following quick-reference points cover the core details most people need to know when servicing a 2012–2015 Civic Si with the 2.4L engine.

• Capacity with filter change: about 4.4 U.S. qt (4.2 L)
• Capacity without filter change: about 4.2 U.S. qt (4.0 L)
• Recommended oil: 0W-20 meeting API SP (or Honda Genuine 0W-20)
• Drain plug torque: 29 lb-ft (39 N·m); replace the crush washer
• Oil filter: tighten by hand (about 3/4 turn after gasket contact)

These figures align with Honda service information for the K24Z7 and mirror typical capacities across Honda’s K24 family. Always confirm with your specific owner’s manual, as small year-to-year or regional differences can exist.

How to change the oil on a 2.4L Civic Si

If you’re planning a DIY oil change, the steps below outline a straightforward process and highlight critical checks to get the fill level right.

1. Warm the engine briefly, then shut it off and safely raise/support the car.
2. Remove the drain plug and crush washer; drain the oil completely.
3. Install a new crush washer and torque the drain plug to 29 lb-ft (39 N·m).
4. Replace the oil filter (lightly oil the new gasket; hand-tighten ~3/4 turn).
5. Add 4.0–4.2 qt of 0W-20, start the engine for 30–60 seconds, then shut it off.
6. Wait a few minutes, check the dipstick, and top up slowly toward 4.4 qt total as needed.
7. Verify the level is between the dipstick’s low and full marks; inspect for leaks.

Because residual oil can vary, it’s best to start slightly low and approach the final level gradually. The dipstick is the final authority—use it to confirm a proper fill.

Tips to avoid overfilling or underfilling

Even with listed capacities, real-world drains can differ. These tips help ensure an accurate fill and healthy engine operation.

• Measure what you drain if possible; it helps benchmark the refill.
• Add oil in stages and recheck after the engine circulates new oil.
• Park on level ground when checking the dipstick for a true reading.
• Replace the crush washer every oil change to prevent seepage.
• Overfilling can aerate oil and harm the catalytic converter; underfilling risks lubrication loss—aim for the dipstick’s upper mark without exceeding it.

Following these practices reduces guesswork and protects the engine from the common pitfalls of incorrect oil levels.

What if your model year differs?

If your Civic is not a 2012–2015 Si, it may have a different engine and capacity. For example, non-Si 1.8L Civics of the same era typically use less oil (around 3.9–4.0 qt), while earlier Si models with the 2.0L engine can differ slightly (often around 4.6 qt with filter). When in doubt, consult your owner’s manual or the under-hood label for the exact spec.

Bottom line

The 2.4L Honda Civic Si (2012–2015, K24Z7) generally takes about 4.4 U.S. quarts (4.2 liters) of 0W-20 with a new filter. Start a little low, warm and recheck, and use the dipstick to set the final level precisely.

Summary

Answer: Approximately 4.4 U.S. qt (4.2 L) with filter, 4.2 U.S. qt (4.0 L) without, using 0W-20. This applies to the 2012–2015 Civic Si with the 2.4L K24Z7 engine. Confirm in your owner’s manual and use the dipstick to verify the final level after refilling.

How many quarts does a Honda 2.4 engine take?

If its a 2.4l it should be around 4.5 quarts.

How much oil does a 2015 Honda Civic 2.4 take?

4.4 quarts
Engine Oil
4.4 quarts (with filter).

What kind of oil does a 2013 Honda Civic 2.4 take?

AMSOIL OE 0W-20 100% Synthetic Motor Oil.

How much oil does a 2.4 l Honda Civic take?

2.4L Engine (Si models): 4.4 quarts (4.2 liters) with filter change.