How Much Oil a 2.4L Honda CR‑V Takes

Most 2.4L Honda CR‑V engines take between 4.4 and 4.6 US quarts of oil with a new filter, depending on the model year. Earlier 2.4L models (2002–2014) are typically 4.4 qt (4.2 L), while later 2.4L models (2015–2019) are about 4.6 qt (4.4 L). Always confirm with the dipstick after filling.

Why the Capacity Varies by Year

Honda used different versions of the 2.4‑liter four‑cylinder across CR‑V generations. While the displacement stayed the same, changes in engine design and oiling systems slightly altered the refill volume. That’s why you’ll see a small difference—about 0.2 US quarts—between older and newer 2.4L CR‑V engines.

Exact Capacities by Generation

The following breakdown shows typical refill capacities with and without a new oil filter, based on Honda owner’s manuals for North American models. Use it to identify your target fill, then fine‑tune via the dipstick to avoid overfilling.

• 2002–2014 CR‑V (2.4L K‑series):
  

  • With filter: 4.4 US qt (4.2 L)
  • Without filter: 4.2 US qt (4.0 L)

• 2015–2019 CR‑V (2.4L “Earth Dreams” K24W, typically LX trim in 2017–2019):
  

  • With filter: 4.6 US qt (4.4 L)
  • Without filter: about 4.3 US qt (4.1 L)

These figures reflect factory guidance for a standard drain and refill. If the engine has been rebuilt, or if the oil cooler or other components have been drained, actual refill may differ slightly.

Recommended Oil Type and Service Notes

Honda specifies 0W‑20 full‑synthetic oil for all 2.4L CR‑V engines in North America. Use oil meeting API SP (or earlier SN/SN Plus) and ILSAC GF‑6 standards. Replace the crush washer on the drain plug, and torque the drain bolt to factory spec (commonly around 30 lb‑ft/40 N·m; check your manual).

Practical Tips for a Clean, Accurate Fill

The points below help ensure you hit the correct level and protect the engine.

1. Warm up the engine briefly, then shut it off and drain to help old oil flow out.
2. Replace the filter at each oil change to maintain the intended capacity and filtration.
3. Add about 90% of the listed capacity, wait a minute, then check the dipstick and top up slowly.
4. After starting the engine for 30 seconds, shut it down, wait a couple of minutes, and recheck the dipstick.
5. Keep the level between the dipstick’s low and high marks; avoid overfilling.

Following these steps minimizes the risk of underfilling or overfilling and helps the engine reach proper oil pressure quickly.

Bottom Line

If your Honda CR‑V has the 2.4‑liter engine, expect roughly 4.4 US quarts (4.2 L) with filter for 2002–2014 models and about 4.6 US quarts (4.4 L) with filter for 2015–2019 models. Confirm by year and verify with the dipstick after filling.

Summary

2.4L Honda CR‑V oil capacity is typically 4.4–4.6 US quarts with a new filter, depending on model year: 4.4 qt (4.2 L) for 2002–2014, and about 4.6 qt (4.4 L) for 2015–2019. Use 0W‑20, check the dipstick after filling, and avoid overfilling.

How much oil does a 2016 Honda CR-V 2.4 take?

A 2016 Honda CR-V with the 2.4L engine requires 4.6 quarts (with filter) of 0W-20 full synthetic oil for an oil change. This includes the oil filter change.

How much oil does a 2.4 Honda CR-V take?

A Honda CR-V with the 2.4L engine typically takes about 4.4 to 4.7 quarts of oil with a filter change, though this amount can vary slightly depending on the specific model year. For example, some sources list 4.2 quarts without a filter change, while others state 4.6 or 4.7 quarts with a filter. Always check your owner’s manual and the dipstick after an oil change to confirm the correct level.
 
Here’s a general guide based on common model years: 

• 2016 Honda CR-V: 4.6 quarts (with filter)
• 2015 Honda CR-V: 4.6 quarts (with filter)
• 2010 Honda CR-V: 4.4 quarts (with filter)
• 2006 Honda CR-V: 4.4 quarts (with filter)

Important Steps:

1. 1. Identify your model year: . Opens in new tabOil capacities can change between generations, so it’s crucial to know your vehicle’s year. 
2. 2. Locate your owner’s manual: . Opens in new tabThe owner’s manual will provide the most accurate information for your specific CR-V. 
3. 3. Perform the oil change: . Opens in new tabAfter adding the recommended amount, start the engine to circulate the oil and then check the level on the dipstick to ensure it’s within the correct range. 

How much oil does a 2015 Honda CR-V 2.4 take?

The 2015 Honda CR-V with the 2.4L engine requires 4.6 quarts (4.4 liters) of 0W-20 synthetic motor oil when changing the oil and filter. After refilling, it is important to check the oil level and then start the engine to ensure it is at the correct mark.
 
Steps for checking oil level:

1. After adding the oil, close the fill cap and start the engine. 
2. Let the engine run for a short time to circulate the oil. 
3. Turn off the engine and wait a few minutes for the oil to settle. 
4. Check the oil level using the dipstick to ensure it is within the recommended range. 
5. Reset the oil maintenance reminder light. 

How much oil does a 2.4 L 4 cylinder Honda take?

0W20. This is going to take 4.2 quarts so it’s going to take. Almost this whole jug but not all of it. So I’m going to go for about four quarts.