How Much Oil a 2007 Audi A4 2.0 Turbo Takes

A 2007 Audi A4 with the 2.0T (2.0-liter turbocharged) engine typically requires about 4.3 to 4.6 liters (approximately 4.5 to 4.9 US quarts) of oil with a filter change, depending on the exact engine variant and market. This article explains the details behind that figure, how to verify it for your specific car, and what type of oil you should use for safe, reliable operation.

Official Oil Capacity: What Audi Specifies

The 2007 Audi A4 2.0 Turbo is usually equipped with the 2.0T FSI four‑cylinder engine (engine code BGB/BWE/BPG, depending on market). Audi’s technical documentation and service data for these engines show a capacity in the mid‑4‑liter range when changing both the oil and filter.

Typical Capacity Range

For most 2007 Audi A4 2.0T models, the engine oil capacity is:

• Approximately 4.3–4.6 liters of oil with filter (about 4.5–4.9 US quarts).
• Closer to the upper end of the range if the engine is fully drained and a new filter is installed.
• A small variation possible between sedan/Avant and front‑wheel drive vs. quattro, but only by a few hundred milliliters at most.

This range reflects common service data for the 2.0T FSI engine family and matches what most professional workshops use in practice, while still allowing room for a final dipstick check rather than relying on an exact number alone.

How to Confirm the Exact Capacity for Your Car

Although the above figures apply to the majority of 2007 Audi A4 2.0T cars, it is always best to verify against your specific vehicle, since equipment, market, and slight engine variations can influence the published number by a few hundred milliliters.

Best Sources for Verification

Several reliable references can be used to confirm the exact oil capacity for your particular A4:

• Owner’s manual: The lubrication or maintenance section normally lists the oil capacity “with filter change.”
• Under‑hood sticker or service label: Some cars have a service sticker noting the recommended oil spec and sometimes capacity.
• Dealer or authorized Audi service: Can look up your car by VIN to confirm the exact engine code and specs.
• Professional repair databases (e.g., manufacturer workshop manuals, trusted repair data services): Used by independent shops to obtain official capacities.

Using these sources ensures you’re not relying solely on “rule of thumb” numbers and that any regional differences in engine specification are properly accounted for.

Recommended Procedure When Filling Oil

Even when you know the approximate capacity, the safest approach is to add oil in stages and use the dipstick to confirm the final level, rather than pouring in the full theoretical amount at once.

Step‑by‑Step Filling Strategy

The following approach helps you avoid overfilling while still reaching the correct operating level:

1. Drain the old oil completely by warming the engine, then removing the drain plug and allowing it to drip until nearly stopped.
2. Replace the drain plug with a new crush washer and install a new oil filter.
3. Add about 4.0 liters (roughly 4.2 US quarts) of fresh oil initially.
4. Wait a minute or two for oil to settle, then check the dipstick and add oil in small increments (e.g., 0.1–0.2 liters at a time).
5. Continue adding until the dipstick is between the MIN and MAX marks, ideally close to the upper mark but not over it.
6. Start the engine, let it run for 30–60 seconds, shut it off, wait a few minutes, and re‑check the level, topping up if needed.

This method accounts for small real‑world variations in how thoroughly the old oil drains, the specific filter model used, and the angle of the car, ensuring you hit the correct level rather than a purely theoretical number.

What Type of Oil a 2007 Audi A4 2.0T Should Use

Getting the capacity right is only half the job; it’s equally important to use oil that meets Audi’s specifications for the 2.0T FSI engine, which is known to be sensitive to oil quality.

Viscosity and Specification

When selecting oil, you should match both viscosity and the official VW/Audi approval standard:

• Typical viscosity (depending on climate):
  

  • 5W‑40 full synthetic (common choice in many regions).
  • 5W‑30 full synthetic meeting the correct VW spec.

• VW/Audi specification:
  

  • Look for VW 502 00 (for fixed service intervals) on the bottle for a 2007 A4 2.0T.
  • If you are on extended “LongLife” intervals (where applicable), oils meeting VW 504 00 / 507 00 may be specified.

• Full synthetic only: Due to turbocharger heat and the design of the FSI engine, conventional oils are not recommended.

Selecting an oil that meets or exceeds Audi’s VW 502 00 (or 504/507 where specified) standard is crucial for turbocharger protection, minimizing deposits, and reducing the risk of sludge or premature engine wear.

Why the Capacity Matters for the 2.0T Engine

The 2.0T FSI engine in the 2007 Audi A4 is known for strong performance but also for being particular about oil level and quality. Both running low and overfilling can cause issues over time.

Risks of Incorrect Oil Level

Maintaining the correct oil level protects the engine, turbocharger, and emissions system from avoidable damage and excessive wear.

• Too little oil:
  

  • Reduced lubrication and cooling, especially at the turbocharger.
  • Increased risk of metal‑to‑metal contact, leading to bearing and cam follower wear.
  • Possible oil pressure warnings and accelerated engine damage if left unchecked.

• Too much oil:
  

  • Oil can aerate (foam), reducing effective lubrication.
  • Increased chance of oil getting into the intake system through the PCV system.
  • Potential catalytic converter and O2 sensor contamination if excess oil is burned.

• FSI and turbo sensitivity:
  

  • Higher operating temperatures and direct injection mean oil degrades faster if not up to spec.
  • Keeping the level near the upper mark with the right spec oil helps longevity.

Because of these sensitivities, treating the published capacity as a guideline and carefully confirming the final level with the dipstick is especially important on this engine family.

Summary

A 2007 Audi A4 2.0 Turbo typically takes about 4.3–4.6 liters of oil, or roughly 4.5–4.9 US quarts, when the oil and filter are changed. The prudent approach is to add around 4.0 liters first, then top up gradually while checking the dipstick until the level sits just below the MAX mark. Use a high‑quality full synthetic oil that meets VW 502 00 (or Audi’s specified VW standard for your service regime) to safeguard the 2.0T FSI engine and its turbocharger. Always confirm final capacity and specifications against your owner’s manual or dealer data for your exact VIN to ensure accuracy.

What kind of oil does a 2007 Audi A4 take?

Mobil 1 FS Full Synthetic Engine Oil 5W-40 5 Quart.

What kind of oil does an Audi A4 2.0 turbo take?

Choosing the Best Oil for Your Audi A4
Audi recommends using synthetic oil that meets the VW 502 00 specification. Here are a few top choices: Castrol EDGE 5W-30 Full Synthetic Motor Oil: Known for its exceptional strength under high pressure, this oil provides superior protection and performance for your Audi A4.

How much oil does a 2.0 Audi A4 take?

5.5 quarts (with filter).

How many quarts of oil does a 2007 Audi A4 2.0 T take?

Capacity: 4.8 quarts (with filter). After refill check oil level.