How much oil does a 2013 Honda Accord 2.4L take?

With a new filter, the 2013 Honda Accord 2.4L takes about 4.6 US quarts (4.4 liters) of engine oil; without replacing the filter, it’s roughly 4.3 US quarts (4.1 liters). This applies to the 2.4L inline‑four “Earth Dreams” engine used across most 2013 Accord trims, and it should be filled with 0W‑20 oil that meets current API/ILSAC specs.

What owners should know about the 2.4L Accord’s oil capacity

Honda’s 2.4L K24W-series engine in the 2013 Accord is designed for low-viscosity 0W‑20 oil. The stated capacity assumes a standard drain and refill. Minor variation is normal due to residual oil in the gallery and filter, so always use the dipstick to confirm the final level after refilling and running the engine briefly.

Recommended oil and key specifications

Below are the key specs and best practices that match Honda’s guidance and modern oil standards for this engine.

• Oil capacity: 4.6 US qt (4.4 L) with filter; 4.3 US qt (4.1 L) without filter
• Viscosity: 0W‑20
• Specifications: API SP (or SN/SN Plus), ILSAC GF‑6A (current) or GF‑5 (previous)
• Drain plug torque: 29 lb‑ft (39 N·m)
• Oil filter installation: light film of oil on gasket, then hand-tighten plus about 3/4 turn, or torque to ~9–12 lb‑ft (per filter maker’s spec)
• Crush washer: 14 mm aluminum—replace at each oil change

Adhering to these specifications helps ensure proper lubrication, fuel economy, and long-term engine health, while minimizing leaks from the drain plug and filter.

Quick reference: how to fill correctly

If you’re changing the oil yourself, this quick checklist helps you hit the correct capacity without overfilling.

1. Warm the engine briefly, then drain oil and replace the filter and crush washer.
2. Add 4.2–4.4 quarts initially (a bit under the full “with filter” spec).
3. Start the engine for 30–60 seconds, shut off, wait a few minutes, and check the dipstick.
4. Top up in small increments to reach the upper dipstick mark—typically reaching about 4.6 quarts total with a new filter.
5. Check for leaks at the drain plug and filter after a short drive, then recheck level.

Filling slightly under and topping up based on the dipstick helps account for small variations and prevents overfilling, which can aerate oil and reduce protection.

Why capacity can vary slightly

A few practical factors may change the exact amount your engine accepts.

• How long the oil was allowed to drain (more time = a bit more capacity)
• Filter size or brand (minor internal volume differences)
• Vehicle level vs. nose-up on ramps during draining and filling
• Residual oil trapped in galleries and the old filter

These small differences are normal; using the dipstick after a brief run-in remains the best way to confirm the final level.

Service interval note

Follow the Maintenance Minder in the instrument cluster for change intervals. If you don’t have the minder, a conservative baseline for mixed driving with quality synthetic 0W‑20 is about 5,000–7,500 miles (8,000–12,000 km), adjusting for severe use like frequent short trips, extreme temperatures, or heavy loads.

Summary

The 2013 Honda Accord 2.4L takes about 4.6 US quarts (4.4 liters) of 0W‑20 oil with a filter change and about 4.3 quarts (4.1 liters) without. Use API SP/ILSAC GF‑6A (or SN/GF‑5) oil, torque the drain plug to 29 lb‑ft with a new crush washer, and confirm the final level on the dipstick after a brief run to ensure an accurate fill.

How much oil does a 2.4 L 4-cylinder take?

How much oil does a 2.4L 4-cylinder take? In general, a 2.4L 4-cylinder engine (found in many vehicles including Honda and other brands) requires around 4.4 to 4.5 quarts (about 4.2 to 4.3 liters) of oil with a filter change. Always use the correct oil type specified by the manufacturer.

Can I put 5W-30 instead of 5W-20 on a Honda Accord?

You can typically use 5W-30 instead of 5W-20 for a short period, but it’s best to stick to the manufacturer’s recommendation, which is usually found on the oil cap or in the owner’s manual, as the engine was designed for a specific oil viscosity. Using a thicker 5W-30 oil may slightly reduce fuel economy and increase engine friction, though it could offer better lubrication or help if the engine is consuming too much 5W-20 oil. 
Why it matters

• Viscosity: . Opens in new tabThe “W” number in 5W-20 and 5W-30 indicates the oil’s flow in cold temperatures, while the second number shows its thickness at operating temperature. 
• Engine Design: . Opens in new tabHonda designs its engines with specific oil viscosities in mind for optimal performance, which includes fuel efficiency and proper lubrication. 

Potential Impacts of Using 5W-30

• Fuel Economy: . Opens in new tabYou may notice a slight decrease in fuel economy because the 5W-30 oil is thicker, requiring more energy to circulate through the engine. 
• Engine Friction and Wear: . Opens in new tabA heavier oil can increase engine friction and may affect the oil pump’s performance. 
• Engine Wear: . Opens in new tabWhile 5W-30 might provide better lubrication in some cases, the overall impact on wear depends on how the engine was originally designed. 

When to Consider 5W-30

• Temporary Solution: If you need to use 5W-30 because 5W-20 is not available, it’s generally not a major concern for a short-term situation. 
• High-Mileage Engines: Some drivers of older, high-mileage Honda engines switch to 5W-30 to help manage oil consumption issues caused by wear on engine components like piston rings. 

What to Do Next

1. 1. Check Your Owner’s Manual: Always refer to your Honda Accord’s owner’s manual to confirm the recommended oil viscosity for your specific model year. 
2. 2. Use the Recommended Oil: For long-term use, it’s best to use the oil viscosity that the engine was designed for to maintain optimal performance, fuel economy, and engine health. 

How many quarts of oil does a 2.4 l Honda Accord take?

A 2.4L Honda Accord generally takes 4.2 to 4.4 quarts of oil with a filter change, though the exact amount can vary by model year. To be certain, you should check your vehicle’s owner’s manual or the oil viscosity cap under the hood for the precise amount. 
How to Determine the Exact Amount

1. Check the Owner’s Manual: The most accurate information will always be in your car’s owner’s manual. 
2. Look at the Oil Cap: The recommended oil viscosity, and sometimes the capacity, is printed on the oil fill cap under the hood. 
3. Consult an Online Tool: Websites like AMSOIL allow you to look up your specific year and model for accurate oil capacities. 

Important Considerations

• Fill Slowly and Check Often: When adding oil, pour it in slowly and check the dipstick frequently to avoid overfilling. 
• New vs. Used Cars: Older vehicles may sometimes be spec’d for slightly different oil weights or require more oil than the standard amount to reach the full mark on the dipstick. 
• Oil Filter: Always replace the oil filter when you change the oil. 

How much oil does a 2013 Honda Accord 2.4 take?

The 2013 Honda Accord with the 2.4L engine requires 4.4 quarts of 0W-20 full synthetic motor oil when performing an oil and filter change. It’s crucial to use a new drain plug washer, check your owner’s manual for the exact oil specification, and verify the oil level with the dipstick after changing. 
Key Details:

• Oil Capacity: 4.4 quarts (with filter) 
• Oil Type: 0W-20 Full Synthetic 
• Drain Plug Washer: Always replace the washer with a new one. 
• Verification: After refilling the oil, start the engine to circulate the oil and then check the dipstick to ensure the level is correct.