How Much Oil a 2014 Audi A4 2.0 TFSI Takes

The 2014 Audi A4 with the 2.0 TFSI engine typically takes about 4.6 quarts (4.4 liters) of engine oil with a filter change, but the exact capacity can vary slightly by specific engine code and market, so confirming against the owner’s manual or VIN-based data is essential.

Understanding the 2014 Audi A4 2.0 TFSI Oil Capacity

The 2014 Audi A4 2.0 T is equipped with a turbocharged 2.0-liter four-cylinder TFSI engine. While it’s often treated as a single engine type, there are minor variations by engine code and region that can influence the precise oil capacity by a few tenths of a quart. Most U.S.-spec and European B8/B8.5 A4 models with the 2.0 TFSI fall into a narrow range around 4.6 quarts (4.4 liters) when the oil filter is replaced during an oil change.

Typical Oil Capacity for the 2014 A4 2.0 T

The figures below summarize the widely published, manufacturer-aligned capacities for the 2014 Audi A4 2.0 TFSI, based on service data used by dealers and independent shops.

• With oil filter change: approximately 4.6 US quarts (about 4.4 liters)
• Without oil filter change: slightly less, around 4.2–4.4 US quarts (about 4.0–4.2 liters)
• Oil level should sit between the MIN and MAX marks on dipstick or MMI display
• Always top off gradually and re-check level after the engine has run and cooled briefly

These values are close to universal for the 2.0 TFSI in the 2014 A4, but a careful check against the car’s documentation or a VIN-specific lookup helps ensure you do not underfill or overfill the engine.

Why Capacity Can Vary Slightly

Even among 2014 Audi A4 2.0 T models, minor differences can change how much oil the engine actually “takes” when refilled after a drain.

Engine Code and Market Differences

Audi’s 2.0 TFSI engines in the 2014 A4 may be listed under different engine codes (such as CAEB, CPMB, etc., depending on market and production run). While the block and displacement are the same, ancillary components and sumps can vary slightly, changing the effective capacity by a small margin. This is why many manuals and professional systems specify an approximate capacity and then emphasize checking level rather than blindly dumping in a fixed volume.

Residual Oil and Real-World Fill Amounts

In real workshop conditions, an engine never drains to an absolutely dry state. Some oil remains in galleries, the turbocharger, and other passages. Depending on how long the oil is allowed to drain and whether the car is level, the amount you refill may be slightly less than the theoretical maximum capacity. As a result, technicians typically pour most of the specified capacity, then top off carefully after checking the level.

Recommended Oil Type and Specifications

Getting the volume right is only part of the job; using the correct oil type is equally important, especially for a turbocharged direct-injection engine like Audi’s 2.0 TFSI.

The following list outlines the main oil requirements and best practices for this engine.

• Oil standard: Use oil that meets Audi/VW specification VW 502 00 (for most gasoline 2.0 TFSI engines of this era).
• Viscosity (common choice): 5W-40 fully synthetic is widely recommended and used by many Audi dealers and independent specialists.
• Alternative viscosities: In some climates, 0W-40 or 5W-30 oils that still meet VW 502 00 may be approved—check your owner’s manual for climate-specific advice.
• Fully synthetic only: Due to the turbocharger’s heat and the engine’s design, a high-quality full synthetic oil is strongly preferred and typically required.
• Change interval: Common practice is every 5,000–7,500 miles (8,000–12,000 km), even if a longer interval is permitted by flexible service schedules, to help mitigate carbon build-up and wear.

Sticking to VW 502 00–approved full synthetic oil in the correct viscosity grade helps protect the turbo, reduce sludge and deposits, and maintain performance and fuel economy over the life of the engine.

How to Safely Fill to the Correct Level

Knowing that your 2014 Audi A4 2.0 T takes around 4.6 quarts with a filter change, the next step is making sure you hit the correct level without overfilling.

Step-by-Step Filling Approach

The steps below describe a cautious, workshop-style method to refill the engine after an oil change.

1. Drain the old oil fully with the car level; allow several minutes for oil to finish dripping.
2. Replace the oil filter and ensure the drain plug (with a new crush washer, if applicable) is properly torqued.
3. Pour in about 4.2–4.3 quarts (roughly 4.0 liters) of fresh oil initially, rather than the full estimated capacity.
4. Refit the oil cap, start the engine, let it idle for 30–60 seconds, then shut it off.
5. Wait a few minutes to allow oil to settle back into the sump.
6. Check the oil level using the dipstick (if equipped) or via the MMI oil-level display, ensuring the car is on level ground.
7. Add oil in small increments (about 0.1–0.2 quarts or 100–200 ml at a time) until the level reaches just below or at the MAX mark.
8. Recheck the level after a short drive and another brief cool-down period to confirm it remains within the safe range.

This method accounts for minor variations in drain completeness and avoids the risk of overfilling, which can be harmful to seals, the catalytic converter, and overall engine health.

Risks of Overfilling or Underfilling

While the capacity figure gives a target, what ultimately matters is that the oil sits within the correct range on the level indicator. Running the engine with oil significantly above or below that range can cause problems.

Too Much Oil

Overfilling can cause the crankshaft to whip the oil into foam, reducing effective lubrication. It can also push oil into the PCV system and intake, potentially fouling spark plugs, oxygen sensors, and the catalytic converter. In severe cases, it may increase crankcase pressure and stress seals, leading to leaks.

Too Little Oil

Underfilling is equally dangerous. Low oil levels can starve the turbocharger and upper engine components, especially under hard acceleration or cornering, when oil may slosh away from the pickup. Long-term running with insufficient oil accelerates wear and raises the risk of catastrophic engine damage.

How to Verify the Exact Capacity for Your Specific Car

Although 4.6 quarts (4.4 liters) with a filter change is the widely accepted figure for the 2014 Audi A4 2.0 TFSI, the most authoritative sources are the documents and systems directly tied to your exact VIN.

The following options can help you confirm capacity for your individual vehicle.

• Owner’s manual: Check the maintenance or technical data section for engine oil capacity and approved specifications.
• Dealer or official service center: Provide your VIN and ask for the engine oil capacity and required oil spec as per Audi’s service system (e.g., Elsa/ErWIN).
• Service sticker or records: Review prior service documentation to see what volume was used and what spec oil was installed.
• Professional databases: Many independent shops use manufacturer-linked databases listing capacities; these can confirm your specific engine code’s data.

Cross-checking these sources helps ensure that any subtle differences—such as updated components or region-specific variants—are accounted for in your maintenance routine.

Summary

For a 2014 Audi A4 with the 2.0 TFSI engine, the typical oil capacity with an oil filter change is about 4.6 US quarts (roughly 4.4 liters), with a slightly smaller amount needed if the filter is not replaced. The engine requires high-quality, fully synthetic oil meeting VW 502 00 specifications, commonly in a 5W-40 viscosity. Because minor variations and residual oil can alter the real-world fill, the best practice is to start slightly below the full capacity, then top up carefully while checking the dipstick or MMI display until the level sits within the safe range. For precise confirmation tailored to your exact car, the owner’s manual and VIN-based dealer data remain the final reference.

How much oil does an Audi A4 2.0 T take?

The Audi A4 2.0T oil capacity is typically between 4.5 and 5.5 quarts, with many models requiring around 5.5 quarts with a filter change. However, the exact capacity varies by model year, so it is crucial to consult your specific owner’s manual or check the vehicle’s onboard oil level system to ensure you add the correct amount. 
Oil capacity by model year (approximate)

• 2017-Present: Approximately 5.5 quarts
• 2009-2016: Around 5 quarts
• 2006-2013: Between 4.5 and 4.9 quarts 

Important considerations

• Always verify: The most accurate capacity for your specific vehicle can be found in your owner’s manual or by using the digital oil level check in the car’s MMI system. 
• Check after filling: After adding oil, start the engine and let it run for a minute to circulate the oil. Then, turn it off and check the level again to ensure it is within the correct range. 
• Oil type: Use a synthetic oil that meets the correct Audi/Volkswagen oil quality standard (e.g., VW 502 00) and viscosity grade for your climate. 

How many quarts of oil for a 2014 Audi A4?

The 2014 Audi A4 oil capacity is 4.9 quarts (4.64.64.6 liters) with a filter change, though some sources specify slightly different capacities depending on the specific engine and transmission. It’s crucial to use an approved oil like a synthetic 5W-40 or 5W-30 that meets the specified Audi/VW quality standard. After refilling, always check the oil level to ensure it’s correct. 
2014 Audi A4 oil capacity and details

Capacity	Notes
4.9 quarts (4.64.64.6 liters)	This is the most common capacity with a filter change for the 2.0L engine.
4.9 quarts (4.64.64.6 liters)	Capacity for the 2.0L TFSI (CPMB) engine on the A4 Quattro and allroad models.
4.9 quarts (4.64.64.6 liters)	Capacity for the 2.0L TFSI (CAED) engine on the FWD A4 Sedan model.

(function(){
(this||self).Wufxzb=function(c,e,f,l,k){var d=document.getElementById(c);if(d&&(d.offsetWidth!==0||d.offsetHeight!==0)){c=d.querySelector(“div”);var g=c.scrollWidth-c.offsetWidth,h=Math.min(e?g:0,g);c.scrollLeft=e&&(l||f)?0:h;var a=d.getElementsByTagName(“g-left-button”)[0],b=d.getElementsByTagName(“g-right-button”)[0];a&&b&&(e=RegExp(“\\btHT0l\\b”),f=RegExp(“\\bpQXcHc\\b”),a.className=a.className.replace(e,””),b.className=b.className.replace(e,””),h===0?a.className=”pQXcHc “+a.className:(a.className=
a.className.replace(f,””),k&&c.classList.add(“pA30Ne”)),h===g?b.className=”pQXcHc “+b.className:(b.className=b.className.replace(f,””),k&&c.classList.add(“FpCCub”)),setTimeout(function(){a.className+=” tHT0l”;b.className+=” tHT0l”},50))}};}).call(this);(function(){var id=’_i6UoaYX0N9bvi-gPya-62Ao_201′;var rtl=false;var gecko=false;var edge=false;var soh=false;
(this||self).Wufxzb(id,rtl,gecko,edge,soh);})();
Important considerations

• Verify your engine: The exact capacity can vary slightly by engine and transmission. Always check your owner’s manual or consult a reliable source for your specific vehicle’s details. 
• Use the correct oil: Use a full synthetic oil that meets the recommended Audi/VW oil quality standards (e.g., VW 502 00) with the correct viscosity grade for your climate, such as 5W-40 or 5W-30. 
• Check the level: After the oil change, start the engine and let it run for a few minutes, then check the oil level to ensure it’s correct. Modern Audis often lack a physical dipstick, so you’ll need to check the level through the car’s computer settings. 

What oil is recommended for 2.0 TFSI?

The most commonly recommended oil for the TFSI engine is 5w30. Under extreme conditions on a stock un-tuned engine the 5w30 oil can become to thin and smoke a little causing the engine to burn oil.

How much oil does a 2.0 4 cylinder engine take?

Approximately 5.1 quarts
2.0L turbocharged engine: Approximately 5.1 quarts of oil.