How to Replace 2022 Honda Accord Windshield Wipers

For a 2022 Honda Accord, use a 26-inch blade on the driver side and a 16-inch blade on the passenger side; the arms use a standard 9×3 mm J-hook connector. To replace them, lift each wiper arm, press the release tab on the old blade, slide it off the hook, attach the new blade until it clicks, then lower the arm carefully. Below you’ll find detailed steps, tips, and troubleshooting to ensure a quick, clean, and safe swap.

What You’ll Need

This section outlines the tools and parts that make the job easier and help protect your windshield and the new blades during installation.

• New wiper blades: 26-inch (driver side), 16-inch (passenger side), J-hook compatible
• A soft towel or fender cover to protect the glass and cowl
• Glass cleaner and a microfiber cloth (to clean the windshield and blade edges)
• Thin gloves (optional for grip and to avoid fingerprints on rubber)
• Small flat-blade screwdriver (optional, to gently press connector tabs if needed)
• Owner’s manual (optional reference for Honda’s OEM refill method)

Having the right sizes and a clean, protected work area reduces the chance of streaks and accidental damage if a wiper arm snaps back onto the glass.

Step-by-Step Replacement Guide

Follow these steps to remove the old blades and install new ones on a 2022 Honda Accord with J-hook wiper arms.

1. Park safely: Turn the ignition off and ensure the wipers are fully parked at the bottom of the windshield.
2. Lift the wiper arm: Gently raise the arm away from the windshield until it holds itself up. Place a folded towel on the glass beneath the arm as a safeguard.
3. Release the old blade: Rotate the blade so it’s perpendicular to the arm. Locate the small release tab where the blade meets the J-hook; press the tab and slide the blade downward (toward the base of the arm) to unhook it.
4. Prepare the new blade: Confirm you’re holding the correct length for the side you’re replacing. If your blade includes adapters, install the 9×3 mm J-hook adapter per the blade’s instructions.
5. Attach the new blade: Thread the J-hook through the blade’s opening, then pull upward until it clicks or locks. Give it a gentle tug to confirm it’s secure.
6. Repeat on the other side: Replace the second blade using the same steps, ensuring you use the correct length.
7. Lower the arms carefully: Ease each arm back onto the glass without letting it snap down.
8. Test the wipers: Wet the windshield with washer fluid and run the wipers. Verify smooth, quiet operation and full contact across the sweep.

Completing these steps should take only a few minutes and will restore clear, streak-free wiping when paired with a clean windshield.

Blade Sizes and Compatibility

Use the correct lengths and connector type to ensure proper fit and performance on the 2022 Accord (all trims, including Hybrid; sedan body style has no rear wiper).

• Driver side: 26-inch blade
• Passenger side: 16-inch blade
• Connector: 9×3 mm J-hook (most aftermarket blades ship ready or include a J-hook adapter)
• Types: Beam-style blades offer better all-weather performance and reduce lift at highway speeds; conventional frames are economical; winter blades resist ice buildup
• Compatibility: Major brands list 2018–2022 Accord fitments with these sizes; confirm the J-hook adapter is included before purchase

Matching size and connector ensures full sweep coverage and prevents chatter or missed spots, especially at the blade tips.

Replacing Just the Rubber Refills (Optional)

Honda OEM wiper assemblies can accept rubber refills, allowing you to reuse the existing blade frames. This is slightly more technical but can be cost-effective.

1. Remove the blade assembly from the arm as above.
2. Locate the locking end cap or metal tab on the blade frame and carefully release it.
3. Slide the old rubber refill out, noting the orientation and embedded metal stiffeners (if present).
4. Transfer or install the metal rails into the new refill if required, then slide the refill into the frame tracks until fully seated.
5. Re-secure the end cap or tab, reinstall the blade on the J-hook, and test.

Refills demand careful handling to avoid bending rails or misalignment; if in doubt, replacing the entire blade is quicker and simpler.

Troubleshooting After Installation

If wiping performance isn’t perfect after the swap, these common issues and fixes can help.

• Streaks or haze: Clean the glass thoroughly and wipe the blade edge with a damp microfiber; replace if rubber is nicked.
• Chatter or judder: Ensure the blade is clicked in fully and the windshield is clean; beam-style blades can reduce chatter.
• Missed areas (especially at edges): Verify blade sizes; check arm spring tension and blade seating.
• Lift at highway speeds: Consider beam or winter blades with aerodynamic spoilers; confirm correct lengths.
• Noise on dry glass: Always wet the windshield when testing; running on dry glass accelerates wear.

Most post-install issues come from dirty glass, incorrect blade length, or an adapter not fully locked—quick checks usually resolve them.

Maintenance Tips and Intervals

Good care extends blade life and preserves clear visibility in all weather.

• Clean monthly: Wipe blade edges and the glass with washer fluid or glass cleaner.
• Replace every 6–12 months: More often in hot, sunny, or icy climates.
• Avoid dry wiping: Use washer fluid to reduce friction and wear.
• De-ice first: Use the defroster/ice scraper; don’t force frozen blades free.
• Protect from heat: Shade or garage parking slows rubber degradation.

Routine cleaning and timely replacement keep wipers quiet and effective, improving safety year-round.

FAQs

These quick answers address common questions Accord owners have about wiper replacement.

• Does the 2022 Accord have a rear wiper? No—the sedan has only front wipers.
• Do I need a special adapter? Most aftermarket blades include a J-hook adapter; confirm packaging before buying.
• Can I mix blade types? Yes, but for even performance, many owners use the same style (beam or conventional) on both sides.
• Why are my new blades streaking? New blades can streak on dirty or waxed windshields—clean the glass and blade edges thoroughly.

If uncertainty remains, your owner’s manual and the blade manufacturer’s fit guide are reliable references.

Summary

Replacing the 2022 Honda Accord’s wipers is straightforward: install a 26-inch driver blade and a 16-inch passenger blade on the J-hook arms, ensuring each clicks into place and passes a wet-wipe test. Clean glass, correct sizes, and careful handling deliver quiet, streak-free performance in minutes.

How do you change the wiper blades on a Honda Accord?

Side right away just so you can see it from another point of view it should just kind of slide down. And come right off. And here’s a close-up of the clip on these OEM style wipers where you just kind

Can I replace my wiper blades myself?

Here. Pull it through Slide it right out just like that very simple. So now you want to match these up make sure they’re the same length. And they are 16 in make sure they have the same clips.

What windshield wipers does a 2022 Honda Accord use?

2022 Honda Accord Wiper Blades Size Chart

Car	Driver	Pass.
2022 Honda Accord	26 in.	16 in.

How to lift windshield wipers on a Honda Accord?

Area when you want to prepare your wipers for icy weather or simply want to change out the blades. Here’s how to do it safely. Start with the vehicle on or in accessory mode. Then turn the vehicle.