How to Replace Wiper Blades on a 2019 Honda Civic

Replacing the wiper blades on a 2019 Honda Civic takes about 10–15 minutes and requires no special tools: lift the wiper arms, release the blade’s connector (typically a pinch-tab “Top Lock” on most Civics), slide the old blade off, and click the new blade into place. Most 2019 Civic sedans, coupes, and hatchbacks use 26-inch (driver) and 18-inch (passenger) front blades; hatchbacks also have a rear blade—check your owner’s manual or parts catalog for the exact rear size. Below is a clear, step-by-step guide with fitment notes, safety tips, and troubleshooting.

What you’ll need

Gather these items before you start to ensure a smooth, safe swap without scratching your glass or paint.

• New front wiper blades: commonly 26-inch (driver) and 18-inch (passenger) for 2019 Civic; verify by trim/market and on the packaging fitment chart.
• New rear wiper blade (hatchback only): size varies by trim/market; confirm in the owner’s manual or by VIN lookup.
• Microfiber towel or fender cover to protect the windshield and paint.
• Glass cleaner (optional, for best wipe quality after install).
• Small flat-blade screwdriver (optional, to help lift a locking tab if needed).
• Gloves (optional, for grip and to keep oils off the rubber).

Ensure your new blades include the correct adapter for Honda’s arm style. Most quality blades ship with multi-adapters covering “Top Lock” (pinch-tab) and J-hook arms.

Step-by-step: Front wiper blades (sedan, coupe, and hatchback)

Follow these steps to remove the old front blades and install the new ones securely without damaging the windshield.

1. Park safely and turn everything off. Set the wiper stalk to Off and, if equipped, turn off Auto/Rain-Sensing mode. Remove the key or turn off the ignition.
2. Lift one wiper arm. Gently raise it off the glass until it stays upright. Slide a folded towel under the arm’s hinge area to protect the glass in case it snaps down.
3. Release the connector. On most 2019 Civics, you’ll have a pinch-tab “Top Lock” fitting—squeeze the two small tabs on the sides of the blade’s adapter and slide the blade downward toward the base of the arm to disengage. If yours uses a J-hook, press the small locking tab, pull the blade downward to unhook, then rotate and remove.
4. Remove the old blade. Rotate the blade to about 90 degrees and slide it free of the arm.
5. Match the new blade. Confirm length and orientation against the old one. Install the correct adapter if your new blade requires one.
6. Attach the new blade. For Top Lock: line up the adapter with the arm end and slide it in until it clicks firmly. For J-hook: thread the hook through the opening, pull the blade up into the hook, and lock it until you hear/feel a click.
7. Check the connection. Tug lightly to confirm it’s fully seated and locked.
8. Repeat on the other front wiper. The passenger blade is shorter; don’t mix them up.
9. Lower the arms carefully. Do not let the bare arm snap onto the glass at any point.
10. Clean and test. Wipe the windshield with glass cleaner, start the car, and test at low speed and with washer fluid to confirm smooth, quiet operation.

If you hear chatter or see streaks after installation, clean both the glass and the new rubber edge; recheck that the adapters are fully clicked in and the sizes are correct.

Step-by-step: Rear wiper blade (hatchback only)

Hatchback owners can replace the rear blade in a couple of minutes using a similar process but a different style of connector.

1. Lift the rear wiper arm off the glass. It will hinge upward slightly and may feel springy.
2. Rotate the blade 90 degrees. Turn it so it’s perpendicular to the arm to expose the locking area.
3. Release the lock. Press the small tab at the blade’s hinge and slide the blade away from the arm’s tip. Some versions pull straight out; others slide then lift off.
4. Install the new rear blade. Align the new blade’s mount with the arm and push until it snaps or clicks into place.
5. Lower the arm gently. Test with the rear washer to confirm proper sweep and contact.

Rear sizes can vary by trim and market. Use your owner’s manual or a parts lookup by VIN to ensure the correct length and connector style.

Connector types and how to identify yours

Honda used more than one connector across models and markets. A quick visual check helps you follow the right removal method and choose the correct adapter.

• Top Lock (pinch-tab, 19 mm): Common on 10th-generation Civics. You’ll see a low-profile, rectangular adapter with small squeeze-tabs on each side. To remove, pinch both tabs and slide the blade down off the arm.
• J-hook (9×3/9×4): Looks like a curved hook at the end of the arm. To remove, press the locking tab on the blade adapter, slide the blade down to unhook, rotate, and lift off. To install, thread the hook through the opening and pull up to lock until it clicks.

If your new blade doesn’t seem to fit, verify you’re using the correct adapter insert from the package; most premium blades include several.

Blade sizes and fitment notes

Choosing the right length and style ensures full windshield coverage without chatter or interference.

• Front sizes: Most 2019 Civic sedans, coupes, and hatchbacks use 26-inch (driver) and 18-inch (passenger) blades.
• Rear size (hatchback): Varies by trim/market; check the owner’s manual, the old blade’s stamp, or a parts catalog by VIN.
• Do not upsize: Longer blades can collide at the sweep overlap or hit the cowl/hood and may strain the motor.
• Beam vs. conventional: The Civic typically ships with beam-style blades; replacing like-for-like often yields the best wipe and noise performance.
• Refills vs. complete blades: Honda OEM refills may be available, but complete blade assemblies are quicker to install and often perform better over time.

When in doubt, the glovebox manual and reputable parts catalogs will confirm exact lengths and connector requirements for your VIN and region.

How often to replace and care tips

Proper maintenance extends blade life and keeps visibility high in rain, snow, and road grime.

• Replace interval: Every 6–12 months, or sooner if you see streaking, chatter, splitting, or reduced clearing.
• Clean regularly: Wipe the rubber edge with a damp microfiber cloth and clean the windshield to reduce chatter and haze.
• Winter caution: Free frozen blades before use; don’t run wipers on ice, which tears the rubber and can damage the motor linkage.
• Sun and chemical exposure: Prolonged UV and washer fluid with harsh additives age rubber faster; parking in shade and using quality fluid helps.

Small, routine cleanings plus timely replacement will keep the Civic’s wipers quiet and effective year-round.

Troubleshooting after replacement

If your new blades don’t perform as expected, these quick checks solve most issues.

• Streaks or haze: Clean the glass and blade edge; confirm the blade isn’t coated with protective shipping film.
• Chatter or noise: Ensure the adapter is fully seated and the arm isn’t twisted; clean the glass; verify correct blade length and type.
• Missed areas or lifting at speed: Check for windshield coating buildup; consider beam-style performance blades; confirm arm spring tension.
• Uneven contact: Make sure the blade spine isn’t bent and the arm pivots freely without play.

If problems persist, recheck fitment by VIN and inspect the wiper arm for damage or weak spring tension, which may require arm replacement.

Summary

Swapping wiper blades on a 2019 Honda Civic is a quick DIY: lift the arms, release the connector (usually a pinch-tab Top Lock), slide off the old blades, and click in correctly sized replacements—typically 26-inch driver and 18-inch passenger, with a hatchback-only rear blade verified by manual or VIN. Protect the glass, confirm a solid “click,” and test with washer fluid. With clean glass and timely replacements every 6–12 months, you’ll maintain quiet, streak-free visibility in all weather.

How to replace wiper blades on Honda Civic?

And it actually will not wipe at. All. Same on the bottom. Once you’re done put the wiper blade down. And do the same on the other side i hope this video was helpful.

Can I replace wiper blades myself?

Yes, replacing windshield wipers is a straightforward task that most people can do themselves. It typically involves removing the old blades, figuring out how they attach to the wiper arm, and then attaching the new blades. Most cars have similar attachment mechanisms, but it’s always a good idea to check your vehicle’s owner’s manual for specific instructions. 
This video demonstrates how to change windshield wipers, including how to remove the old blade and attach the new one: 57sAdvance Auto PartsYouTube · Jun 14, 2019
Here’s a general guide:

1. Determine the wiper blade size: You can find this information in your vehicle’s owner’s manual or by measuring the existing blades. You can also check with auto parts stores, who can help you find the right size for your car. 
2. Purchase new wiper blades: Choose the type you prefer (standard, beam, hybrid). 
3. Prepare the windshield: Lay a towel or something similar on the windshield to protect it while you’re working. 
4. Remove the old wiper blade: Lift the wiper arm away from the windshield. Most blades have a clip, button, or tab you’ll need to release to slide the blade off the arm. 
5. Attach the new wiper blade: Slide the new blade onto the wiper arm until it clicks or locks into place. 
6. Test the new blades: Ensure they wipe cleanly and don’t chatter or skip. 

This video shows a simple method for changing windshield wipers using a hook style clip: 1mClark Howard: Save More, Spend LessYouTube · Jun 21, 2018
If you encounter any difficulty or are unsure about the process, don’t hesitate to ask for assistance at an auto parts store or a mechanic.

How to change wiper blades on Honda Civic 2019?

And just push it until it’s tight and snap in the top clip lastly don’t forget about the plastic. Cover. And that’s how you change the wiper blades on your Honda Civic.

How to lift up windshield wipers on Honda Civic?

Area when you want to prepare your wipers for icy weather or simply want to change out the blades. Here’s how to do it safely. Start with the vehicle on or in accessory mode. Then turn the vehicle.