What is the bolt pattern of a 2010 Honda Civic?

The 2010 Honda Civic uses a 5×114.3 mm bolt pattern (also known as 5×4.5″). This applies across the 2010 U.S. lineup—including DX, LX, EX, EX-L, Si, Hybrid, and GX—though owners should always verify if their vehicle has been modified with aftermarket hubs or wheels.

What the bolt pattern means and why it matters

Wheel bolt pattern describes how many lug studs a wheel uses and the diameter of the circle they form. For the 2010 Civic, “5×114.3” means five lugs spaced on a 114.3 mm circle. Matching this spec is essential for safe wheel fitment; a mismatch can prevent mounting, cause vibration, or compromise safety.

Trim and market coverage

In North America, all 2010 Honda Civic variants—coupe and sedan, including Si performance models and the Hybrid—share the 5×114.3 mm pattern and a Honda-standard 64.1 mm center bore. Most global 2010 Civics (eighth generation) follow the same spec, but it’s prudent to confirm if you own a market-specific model or a car with aftermarket conversions.

The following list outlines which 2010 Civic trims use the 5×114.3 mm pattern:

• DX, LX, EX, EX-L (coupe and sedan)
• Si (coupe and sedan)
• Hybrid
• GX (natural gas)

Across these trims, the bolt pattern remains consistent, simplifying cross-fitment within the model year as long as offset and tire size are considered.

Related wheel-fitment specs for the 2010 Civic

Beyond bolt pattern, several measurements help ensure wheels mount correctly and perform as intended. Here are the key specs owners and installers most often reference for a 2010 Civic.

• Center bore: 64.1 mm (Honda standard)
• Lug nut thread: M12 x 1.5
• OEM wheel offset: typically around +45 mm (varies slightly by trim/wheel)
• Common factory wheel sizes/tires:
  – 15×6 with 195/65R15 (DX/Hybrid and some base trims)
  – 16×6.5 with 205/55R16 (LX/EX)
  – 17×7 with 215/45R17 (Si)
• Lug nut torque: approximately 80 lb-ft (108 N·m)

Using these measurements alongside the bolt pattern helps you choose wheels that clear brakes, maintain proper stance, and avoid vibration without relying on spacers or hub rings (unless needed for non-Honda wheels).

Compatibility and cross-fit considerations

Because 5×114.3 mm is a common pattern, many wheels from other brands may physically bolt up. However, center bore and offset often differ by manufacturer, and hub-centric rings or different lug nuts may be required.

• Other Hondas/ Acuras with 5×114.3 and 64.1 mm bore (e.g., many Accord, CR-V, Integra Type R, RSX, TSX years) are typically close matches.
• Brands like Toyota, Mazda, Nissan, and Hyundai also use 5×114.3 on various models, but their center bores and offsets usually differ—verify and use hub rings if needed.
• Always confirm brake caliper clearance and load rating when cross-fitting wheels from other models.

A quick check of center bore, offset, and brake clearance can turn a “bolt-on” candidate into a safe, vibration-free fit.

How to verify your bolt pattern

If you’re unsure about your car’s hardware—especially after modifications—these steps can help you confirm the spec before purchasing wheels.

1. Count the lugs: confirm you have five studs.
2. Measure the circle: for 5-lug wheels, measure from the center of one stud to the far edge of the stud directly across to estimate 114.3 mm.
3. Check the center bore: look for “64.1” stamped on OEM wheels or measure with calipers.
4. Consult documentation: owner’s manual, door-jamb placard, or OEM part catalogs can confirm factory specs.

Verifying these points reduces the risk of ordering incompatible wheels and ensures safe, precise fitment.

Summary

The 2010 Honda Civic uses a 5×114.3 mm (5×4.5″) bolt pattern across all U.S. trims, paired with a 64.1 mm center bore and M12x1.5 lug nuts. Stick close to the OEM-like offset (around +45 mm) and confirm wheel size, hub bore, and brake clearance for a hassle-free upgrade or replacement.

Is the Honda 5×114 3?

Sedans and Coupes. Ford Mustang: One of America’s most iconic sports cars, the Mustang has used the 5×114. 3 bolt pattern for several generations. Honda Accord: A staple in the sedan market, the Accord has featured this bolt pattern in various models over the years.

What is the bolt pattern on a 2010 Honda Civic?

The 2010 Honda Civic has a 5×114.3mm (or 5×4.5 inch) bolt pattern. This applies to all trim levels for that year, including the Si and non-Si models. 
This means the wheel has 5 lug holes, and the distance between any two opposing lug holes is 114.3mm, which is equivalent to 4.5 inches.

Are Honda Civics 4×100?

For Civics, if you have 4 bolts then its 4 x 100mm, 5 bolts is 5 x 114.3mm. These are standard sizes for all years.

What Hondas have 4×100?

Compatibility and Suitability: The 4×100 bolt pattern is predominantly found in compact and subcompact Honda models, such as older Civic models, the Fit, CRX, Insight, Del Sol, Prelude, and City. It’s crucial to verify the bolt pattern for your specific vehicle model and year.