Bolt Pattern on a 2013 Audi Q5: What Owners Need to Know

The 2013 Audi Q5 most commonly uses a 5×112 mm bolt pattern, with a 66.6 mm center bore and typical stock wheel sizes ranging from 17 to 20 inches depending on trim and market. However, exact specifications can vary slightly by engine, brake package, and region, so owners should verify details before buying or installing wheels.

Understanding the 2013 Audi Q5 Wheel Bolt Pattern

For the 2013 model year, the Audi Q5—across its mainstream trims—shares a standard Volkswagen Group SUV bolt pattern. That pattern is expressed as 5×112, meaning the wheel is secured by five lug bolts arranged on a 112 mm diameter circle. This configuration is used across many Audi, Volkswagen, and some Mercedes-Benz models, making wheel compatibility broader than it might appear at first glance, if the other dimensions also match.

Core Wheel Fitment Specifications

Wheel fitment is determined not only by bolt pattern but also by center bore, offset, and lug hardware. The 2013 Audi Q5 follows a fairly consistent set of specifications that guide safe wheel selection and installation.

Key Bolt Pattern and Dimensional Data

The following list outlines the primary factory specifications that matter when selecting wheels for a 2013 Audi Q5, helping ensure proper fit, safety, and performance.

• Bolt pattern (PCD): 5×112 mm (5-lug on a 112 mm pitch circle diameter)
• Center bore (hub bore): 66.5–66.6 mm (often listed as 66.6 mm)
• Lug type: Lug bolts (not studs and nuts), typically M14x1.5
• Typical stock wheel diameter: 17″–20″ depending on trim and package
• Typical stock wheel width: Approx. 7.5″–8.5″
• Typical factory offset range (ET): Roughly ET 25–40, depending on wheel design and size

Taken together, these specifications define the base parameters wheel manufacturers and fitment guides use: the 5×112 pattern and 66.6 mm center bore are non-negotiable baseline figures, while wheel width and offset are used to fine-tune clearance and appearance.

Why the 5×112 Pattern Matters

While many wheels may appear to fit, the bolt pattern is fundamental to safety. The 5×112 layout is not interchangeable with similar-looking patterns such as 5×114.3 or 5×110 without the use of specialty adapters, which themselves introduce complexity and risk if not properly engineered and installed.

Compatibility With Other Vehicles and Aftermarket Wheels

This section details considerations for cross-compatibility and why owners need more than just the bolt pattern before selecting wheels from other vehicles or aftermarket sources.

• Cross-brand fit: Some Audi, Volkswagen, and Mercedes-Benz models also use 5×112 and similar center bores, making cross-fitment possible if offset and hub bore match.
• Center bore alignment: The Q5’s ~66.6 mm hub bore typically requires hubcentric wheels or hubcentric rings if the wheel bore is larger (e.g., 66.6 → 72.6 mm using a ring).
• Offset constraints: Incorrect offset (too high or low) can lead to rubbing on suspension or fenders, altered steering feel, and increased wear on bearings and suspension components.
• Brake clearance: Larger brake packages (such as on higher-performance variants in some markets) may require minimum wheel diameters or specific spoke designs for caliper clearance.
• Load rating: The Q5 is a crossover/SUV; wheels and tires must meet or exceed the vehicle’s load rating, even if bolt pattern matches.

Because of these factors, 5×112 alone is not enough to guarantee a safe or legal fit; center bore, offset, and load capacity must all be confirmed against the Q5’s requirements.

How to Confirm Your Specific Q5’s Bolt Pattern and Wheel Specs

Although the 5×112 pattern and 66.6 mm bore are widely documented for the 2013 Audi Q5, individual vehicles can have variations due to factory packages, regional specs, or retrofitted parts. Verifying your own car’s details is strongly recommended before purchasing wheels.

Practical Ways to Double-Check Fitment

The following methods provide a reliable way to confirm wheel data and avoid costly mistakes, especially if your Q5 has been modified or was originally sold in a different market.

1. Check the owner’s manual: Audi typically lists standard wheel and tire specifications, including sizes and load ratings.
2. Inspect the current wheels: Many OEM wheels have size and offset stamped or cast on the inside of the spokes or rim (e.g., “8Jx18 ET39”).
3. Use the VIN at a dealer: An Audi dealer can decode your VIN and list the factory wheel dimensions and any sport or brake packages affecting minimum wheel size.
4. Consult reputable fitment databases: Established online wheel/tire fitment tools and catalogs (from major wheel brands or tire retailers) often list vehicle-specific specs for the 2013 Q5.
5. Measure directly if uncertain: A qualified shop can confirm bolt pattern, hub bore, and offset on existing wheels and hubs if there is any doubt about originality.

Taking these steps ensures that the 5×112 specification for the 2013 Q5 is not only correct in theory but actually matches your vehicle’s installed components and intended usage.

Aftermarket Wheel Upgrades: What Owners Should Watch For

Owners of the 2013 Audi Q5 often upgrade wheels for aesthetics or performance, but deviating from factory specs without a plan can compromise comfort or safety. Within the 5×112 standard, there is room to customize, but changes should be controlled and well understood.

Common Upgrade Considerations

This list outlines the major factors Q5 owners should balance when changing from stock wheels while retaining the correct 5×112 bolt pattern.

• Diameter changes: Moving from, for example, a stock 18″ wheel to 19″ or 20″ may require lower-profile tires to keep the overall rolling diameter within acceptable tolerances for speedometer, ABS, and traction systems.
• Width and offset: Wider wheels (e.g., 8.5″ or 9″) can enhance grip and stance, but offset must be chosen to maintain adequate clearance from suspension components and fenders.
• Unsprung weight: Heavier wheels can reduce ride comfort and responsiveness, while lighter, high-quality alloys may improve handling but often cost more.
• Winter vs. summer setups: Many Q5 owners run smaller, higher-profile wheels in winter for better ride and protection, keeping the 5×112 pattern but changing size and design.
• Certification and standards: Reputable wheels should carry appropriate certifications (e.g., TÜV, JWL, VIA) and a load rating compatible with an SUV-class vehicle like the Q5.

By keeping the 5×112 pattern and 66.6 mm center bore as fixed constraints and adjusting size and offset thoughtfully, Q5 owners can safely personalize their vehicles without risking mechanical or legal issues.

Summary

The 2013 Audi Q5 uses a 5×112 mm bolt pattern and a center bore of about 66.6 mm, with factory wheels generally in the 17″–20″ range and offsets around ET 25–40 depending on design. While this 5-lug pattern is shared with many other Audi and VW products, correct wheel choice also requires matching hub bore, offset, and load rating. Owners are best served by confirming specs via the owner’s manual, VIN-based dealer information, or reputable fitment tools before purchasing wheels, particularly when upgrading to larger diameters or different widths.

What is the bolt pattern on an Audi Q5?

The Audi Q5 has a bolt pattern of 5×112 for all model years. This means there are five lug bolts with a bolt circle diameter of 112mm.
 
You can watch this video to learn how to check your car’s bolt pattern: 56sDeutsche Auto PartsYouTube · Jan 30, 2020

• 5×112: This indicates five lug holes and a distance of 112 millimeters between the centers of opposite lug holes. 
• Confirmation: This bolt pattern is consistent across various generations, from 2008 to the latest models. 
• Other common Audi/VW bolt pattern: For comparison, some older Volkswagen and Audi models used a 5×100 bolt pattern, but the Q5 uses the more modern 5×112 pattern. 
• Related specifications: When choosing wheels, also consider the center bore, offset, and wheel size, which are specific to the Q5 model and wheel type. The most common center bore is 66.5mm. 

What Audi has a 5×130 bolt pattern?

22″ W627 Style Wheels For Porsche Cayenne and Audi Q7 with 5×130 bolt pattern Up to 2015 on the Q7.

What does a 5×112 bolt pattern fit?

5×112 wheels fit many Volkswagen, Audi, and Mercedes-Benz models, as well as select models from other brands like BMW (newer models), Aiways, and Alfa Romeo. It is crucial to always confirm vehicle compatibility before purchasing, as other factors like offset and hub bore also play a role. 
Common vehicle makes and models

• Volkswagen: Most modern VWs, including the Golf (MK5 and newer), Jetta, Passat, Tiguan, and Arteon. 
• Audi: Various models such as the A3, A4, A5, A6, A7, A8, Q3, Q5, and TT. 
• Mercedes-Benz: Models from the A-Class and C-Class to the E-Class, S-Class, and SUVs like the GLC and GLE. 
• BMW: Select newer models, especially those on shared platforms like some G-chassis models and the i4/iX1. Older BMW models typically use a different bolt pattern. 
• Other brands: Some models from Aiways, Alfa Romeo, Bentley, Seat, and Skoda also use this bolt pattern. 

Important considerations

• Vehicle-specific fitment: Always check the specific fitment for your vehicle’s year, make, and model before buying, as not all vehicles within a brand will use the same pattern. 
• Other specifications: Beyond the bolt pattern, ensure the wheel’s offset, bolt size, and hub bore match your vehicle’s specifications for a correct and safe fit. 
• Adapters: It is sometimes possible to use wheels with a different bolt pattern with the help of adapters, though this can alter the vehicle’s handling characteristics. 

What size tires are on a 2013 Audi Q5?

The Audi Q5 also comes with a range of stock tire sizes, including 235/60R18 tires, 235/55R19 tires, 255/45R20 tires, 255/40R21 tires.