What Is the Bolt Torque on a Honda CR‑V?

There isn’t one universal “bolt torque” for a Honda CR‑V—every fastener has its own specification that varies by model year, engine, and system. As a quick guide, many late‑model CR‑Vs specify about 80–94 lb‑ft (108–127 N·m) for wheel lug nuts and about 29 lb‑ft (39 N·m) for the engine oil drain plug, but you should always verify the exact figure in your owner’s manual or the factory service information for your specific VIN.

Why There Isn’t a Single Torque Spec

Automakers engineer each joint—wheels, brakes, suspension, drivetrain, engine, and body—with different bolt sizes, thread pitches, materials, coatings, and safety factors. Torque requirements also reflect whether a bolt is lubricated, requires a new crush washer, or uses torque‑to‑yield + angle procedures. As a result, torque specs are component‑ and model‑specific, and sometimes change between generations or trims (e.g., turbo vs. hybrid).

Commonly Referenced Torque Specs on Recent Honda CR‑Vs

The items below are among the most frequently requested torque values for routine maintenance and common repairs. Values are typical for recent CR‑V generations and are provided to help you gauge the right ballpark; always confirm the exact spec for your year/trim in official Honda documentation.

• Wheel lug nuts: typically 80–94 lb‑ft (108–127 N·m), depending on year/trim
• Engine oil drain plug (with new crush washer): about 29 lb‑ft (39 N·m)
• Engine oil filter: hand‑tighten per filter instructions; if torqued, roughly 9 lb‑ft (12 N·m)
• Spark plugs (M12 gasketed plugs on late models): about 13 lb‑ft (18 N·m); install dry, no anti‑seize
• Front brake caliper guide/slide pins: roughly 25 lb‑ft (34 N·m)
• Front brake caliper bracket (mounting) bolts: commonly 80–90 lb‑ft (108–122 N·m), model‑dependent
• Front axle spindle/axle nut: commonly ~179 lb‑ft (242 N·m); many models also require a staked nut
• CVT drain plug: commonly ~36 lb‑ft (49 N·m); confirm for your transmission code
• Rear differential (AWD) drain/fill: commonly ~35 lb‑ft (47–49 N·m)
• Valve cover fasteners: often about 7–9 lb‑ft (9–12 N·m), tightened evenly in sequence

These figures cover frequent service points and typical ranges seen across recent CR‑V generations. Differences do exist by year, engine, drivetrain, and even supplier, so treat them as guidance until you verify the exact specification.

How to Find the Exact Torque Spec for Your CR‑V

Because torque values vary, the most reliable way to get the right number is to use Honda’s official sources tied to your model year and VIN.

1. Check your owner’s manual: Common torque specs (like wheel lugs and oil drain plug) are usually listed.
2. Use Honda Service Information (techinfo.honda.com): The factory service manual provides component‑level specs, sequences, and angle‑torque steps.
3. Look for labels and parts notes: Some components (e.g., axle nuts, suspension hardware) include torque notes on packaging or service bulletins.
4. Verify units: Honda often prints specs in N·m; convert carefully to lb‑ft if needed (1 lb‑ft ≈ 1.356 N·m).

Confirming torque from an official Honda source avoids guesswork and helps prevent fastener damage, loosening, or warping of components.

Best Practices When Torquing CR‑V Fasteners

Correct torque is only part of doing the job right; preparation and technique affect clamping force and safety. Keep these practices in mind.

• Use a calibrated torque wrench in the correct range; click‑type tools are most accurate mid‑scale.
• Clean threads and mating surfaces; replace crush washers and single‑use fasteners (e.g., axle nuts) as specified.
• Apply lubricants or threadlocker only if the procedure calls for it; “wet” threads change the torque‑to‑clamp relationship.
• Follow specified sequences and any angle‑torque steps (especially for structural or gasketed joints).
• For wheels, tighten in a star pattern and re‑check torque after 25–50 miles.

Attention to these details ensures the torque you set matches the clamping force the engineers intended, preserving reliability and safety.

Generation and Trim Differences to Keep in Mind

Torque specs can shift across generations and powertrains. For example, late‑model turbo and hybrid CR‑Vs may share many values, but transmission and drivetrain fasteners can differ. Suspension and brake supplier changes can also alter caliper bracket or strut fastener torques. If you’re moving between a 2012–2016 (4th gen), 2017–2022 (5th gen), and 2023–present (6th gen) CR‑V, don’t assume carryover specs—double‑check.

Bottom Line

There’s no single “bolt torque” for a Honda CR‑V. Many common service items fall into familiar ranges—wheel lug nuts around 80–94 lb‑ft and the oil drain plug near 29 lb‑ft—but the safe, correct approach is to verify each fastener in Honda’s official documentation for your exact model year and configuration.

Summary

Torque specs on a Honda CR‑V vary by bolt, year, and system. Typical figures include wheel lug nuts at about 80–94 lb‑ft and the engine oil drain plug at roughly 29 lb‑ft, but exact values must be confirmed in the owner’s manual or Honda’s service information. Use proper tools, observe sequences, and replace single‑use hardware to ensure safe, reliable repairs.

What is the torque spec for a 2016 Honda CRV?

2016 Honda CR-V Specifications & Features

ENGINEERING	LX	Touring
Displacement	2356 cc	2356 cc
Horsepower (SAE net)	185 @ 6400 rpm	185 @ 6400 rpm
Torque (SAE net)	181 lb-ft @ 3900 rpm	181 lb-ft @ 3900 rpm
Bore and Stroke	87 mm x 99.1 mm	87 mm x 99.1 mm

What is the torque on a Honda CRV tire?

Do not use a tire lever to install and remove the tires as it may cause damage to the tire and aluminum wheel. The wheel nut torque is 108 N·m (11.0 kgf·m, 80 lbf·ft). This kit should be installed only if the ambient air temperature is 60°F (15°C) or above.

What is the torque on Honda CRV lug nuts?

The lug nut torque for most Honda CR-V models is 80 ft-lbs (foot-pounds). Always use a torque wrench and tighten the lug nuts in a star pattern to ensure they are securely fastened and to prevent damage from overtightening or undertightening. It’s best to confirm the exact specification in your vehicle’s owner’s manual, as some CR-V models or specific years may have slightly different torque settings.
 
Steps to Properly Torque Lug Nuts

1. Hand-tighten: the lug nuts first after changing a tire. 
2. Use a torque wrench: to tighten the lug nuts to the specified 80 ft-lbs. 
3. Follow a star pattern: (or cross pattern) when tightening to ensure even pressure and proper seating of the wheel. 
4. Re-torque: the lug nuts after driving 50-100 miles. 

Why Proper Torque is Important 

• Overtightening: can damage the wheel studs, lug nuts, or even the wheel itself.
• Undertightening: can lead to wheel vibration, damage, or in extreme cases, the wheel could come off.

What is the torque on the bolts on a Honda CRV?

80 lb-ft
Torque Specifications: When installing wheels on a CR-V, the recommended torque specification is 108 Nm (80 lb-ft), which should be applied in a star pattern for proper wheel seating.