2011 Honda Odyssey Firing Order

The firing order is 1-4-2-5-3-6. On the 2011 Honda Odyssey’s 3.5-liter J-series V6, Bank 1 is the rear bank (firewall side) with cylinders 1-3-5, and Bank 2 is the front bank (radiator side) with cylinders 2-4-6. Knowing this layout helps when diagnosing misfires, replacing coils or plugs, and interpreting Bank 1 and Bank 2 sensor readings.

Cylinder numbering by location

The list below shows where each cylinder is located as you face the engine from the front of the vehicle (North American 2011 Odyssey, transverse-mounted J35 V6).

• Rear bank (firewall side, Bank 1): 1 = passenger side, 3 = middle, 5 = driver side
• Front bank (radiator side, Bank 2): 2 = passenger side, 4 = middle, 6 = driver side

This numbering is standard across Honda’s J-series V6s and ensures you can correctly identify cylinders for maintenance or diagnostics.

Ignition order for the J35 V6

The following ordered list shows the ignition sequence that repeats continuously while the engine runs.

This 1-4-2-5-3-6 pattern applies to all 2011 Odyssey trims (with or without Variable Cylinder Management) because they use the same J-series 3.5-liter V6 architecture.

Practical Notes for Maintenance and Diagnosis

While the Odyssey utilizes coil-on-plug ignition (eliminating the need for traditional plug wires to follow a firing order sequence), the firing order and cylinder numbering still matter for troubleshooting and service purposes.

• Misfire diagnosis: Codes like P0301–P0306 map directly to cylinders 1–6. Use the cylinder layout above to find the correct coil/plug.
• Coil/plug checks: Swapping a suspected coil from, say, cylinder 1 to cylinder 4 can confirm if a misfire follows the coil.
• Spark plug service: Iridium plugs are pre-gapped (about 0.039–0.043 in / 1.0–1.1 mm) and should be torqued to roughly 13 lb-ft (17–18 N·m) unless your service manual specifies otherwise.
• Bank references: “Bank 1” sensors (such as O2 or A/F sensors) are on the rear bank with cylinders 1–3–5; “Bank 2” is the front bank with 2–4–6.

Following these basics will help you avoid mix-ups and speed up accurate repairs.

Summary

The 2011 Honda Odyssey’s 3.5L J-series V6 fires in the order 1-4-2-5-3-6. Cylinder numbering is 1-3-5 at the rear (firewall side, Bank 1) and 2-4-6 at the front (radiator side, Bank 2). This information is essential for correct diagnostics and maintenance, even with coil-on-plug ignition.

What is the cylinder order for a 3.6 V6?

So without wasting any more time let’s get started the firing order for the Dodge 3.6 Pennar engine is 1 2 3 4 5 6. This means cylinder 1 fires.

Where is the cylinder 3 on a 2011 Honda Odyssey?

On the 2011 Honda Odyssey’s 3.5L V6 engine, cylinder #3 is located on the Bank 1 (the row closest to the firewall/driver’s side), specifically the right side of the engine compartment from the front of the vehicle. It is the third cylinder from the passenger side.

1. Front of Engine: The part of the engine closest to the vehicle’s radiator (and the front of the car).
2. Bank 1: This is the row of cylinders on the right side of the engine compartment when you are facing the front of the vehicle.
3. Cylinder #3: Cylinder #3 is the third cylinder from the passenger side (the front of the engine) on this bank.

Which cylinder is number 2 on a Honda Odyssey?

Information that row of cylinders is going to be called bank. One. And then on the left side of the engine that’s the side of the engine closest to the radiator. You’re going to have cylinders.

What is the order of cylinders on a 2012 Honda Odyssey?

The 2012 Honda Odyssey 3.5L V6 engine has cylinders numbered 1-3 on the front bank and 4-6 on the rear.