2014 Honda City i-VTEC Wiper Blade Sizes

The front wiper blade sizes for a 2014 Honda City i-VTEC sedan are typically 26 inches (650 mm) on the driver’s side and 14 inches (350 mm) on the passenger’s side, with no rear wiper on the sedan. These sizes fit most markets where the 2014 City (GM6/GM2 platforms depending on region) was sold; a few accessory catalogs list a 16-inch (400 mm) passenger blade as an alternative, but 14 inches is the most common factory fit.

Fitment Details, Variants, and What to Check

Honda delivered the 2014 City primarily as a sedan, and it uses asymmetrical front wiper lengths to maximize sweep without hitting the A‑pillar or cowl. In most regions (including India and Southeast Asia), the OEM specification is 26 inches for the driver’s blade and 14 inches for the passenger’s blade. Some aftermarket guides occasionally suggest a 16-inch passenger blade; this can fit on some cars but may touch the windshield trim at the extremes of travel, so verify clearance before finalizing.

Wiper Arm Type and Adapter Compatibility

The 2014 Honda City i-VTEC typically uses a standard 9×3 mm “J-hook” (U-hook) wiper arm. Most beam, hybrid, or conventional replacement blades include the correct adapter for this hook type. If you’re reusing OEM holders with rubber refills, look for refills in 650 mm (driver) and 350 mm (passenger) lengths.

Popular Replacement Options and Sizes

The following examples illustrate common replacement choices that fit the 2014 Honda City i-VTEC. Always match the blade length and the J-hook adapter before purchase, and prefer beam or hybrid designs for quieter, streak-free performance.

• Beam/hybrid blades: 26″ (650 mm) driver + 14″ (350 mm) passenger sets from leading brands (Bosch, Valeo, Trico, Michelin) with J-hook adapters.
• Conventional frame blades: Individual 26″ and 14″ blades, if you prefer traditional metal-frame designs.
• Rubber refills (for OEM rails): 650 mm (driver) and 350 mm (passenger) refills if your original holders are in good condition.
• Alternative fit seen in some catalogs: 26″ driver + 16″ passenger; use only if you’ve confirmed no contact with the cowl or A-pillar through the full sweep.

Choosing a reputable brand with the correct length and hook adapter is more important than the specific model line; the key is ensuring clean windshield contact and proper clearance.

Installation Tips and Troubleshooting

Replacing wiper blades is a quick DIY job. The steps below help ensure correct fitment and quiet operation, and the checks help diagnose streaking or noise after installation.

1. Lift each wiper arm and align the new blade’s J-hook adapter with the arm’s hook; slide and click into place.
2. Gently lower the arm onto the glass; avoid snapping it down to prevent windshield damage.
3. Test the wipers on a wet windshield to confirm smooth, silent operation and full clearance at the cowl and A-pillar.
4. If you see streaks, clean the windshield and blade edge with glass cleaner or isopropyl alcohol; replace if rubber is nicked or hardened.
5. In hot climates, consider UV-resistant blades; in heavy monsoon areas, beam blades with uniform pressure distribution often last longer.

Proper installation and routine cleaning usually resolve chatter or streaking; if problems persist, inspect arm tension or consider a higher-quality beam blade.

Frequently Asked Questions

These quick answers address common points of confusion about the 2014 Honda City’s wiper setup and compatibility.

• Rear wiper? The 2014 City sedan does not have a rear wiper.
• Left-hand-drive vs right-hand-drive? The blade lengths are the same; only the sweep pattern changes.
• Can I upsize the passenger blade to 16″? Sometimes, but check for contact at the extremes of the sweep before using it long-term.
• Best type? Beam (flat) blades typically offer the quietest, most even pressure across curved glass.
• Service interval? Inspect every 6 months; replace roughly every 6–12 months depending on climate and use.

Following these guidelines will help you choose the right parts and avoid fitment issues or premature wear.

Summary

For a 2014 Honda City i-VTEC sedan, the standard wiper blade sizes are 26 inches (driver) and 14 inches (passenger), with a J-hook arm and no rear wiper. While some aftermarket listings show a 16-inch passenger alternative, the 14-inch length is the most widely correct fit; verify clearance if considering upsizing. Opt for quality beam blades, install with the J-hook adapter, and maintain them regularly for clear, streak-free visibility.

What size wiper blades for Honda City Ivtec?

Frameless Wiper Blades for Honda City i-Vtec (24 x 14)

What size windshield wipers for 2014 Honda Fit?

28″/14″
3 wipers Replacement for 2009-2020 Honda Fit, Windshield Wiper Blades Original Equipment Replacement – 28″/14″/14″ (Set of 3) U/J HOOK.

How do I tell what size wipers I need?

First, check your owner’s manual. While typically an OEM does not provide a standard wiper size, your owner’s manual may provide one, depending on your vehicle’s make and model. If that’s not the case, you can either: Using a tape measure, measure your existing wiper blades — driver side, passenger side, and rear.

What size windshield wipers for 2014 Honda?

Starting with the size, you’ll need a 26-inch blade on the driver’s side and a 19-inch blade on the passenger’s side.