Where to Find the Oil Filter on a 2014 Honda Accord

It’s mounted low on the front (radiator side) of the engine block and is easiest to reach from underneath after removing the plastic splash shield: on 2.4L four-cylinder models it sits toward the passenger side and faces forward; on 3.5L V6 models it’s near the lower front-center of the engine facing forward; and on Hybrid (2.0L) models it’s low on the front driver’s side, usually angled slightly downward. In all cases, access is typically from below with the front of the car safely raised and the engine under-cover removed.

Location by Engine Type

The 2014 Accord was sold with three powertrains, and the oil filter’s exact spot varies slightly. Use the descriptions below to pinpoint it on your specific engine.

• 2.4L Inline-4 (K24W “Earth Dreams”): Front of the engine, low and slightly toward the passenger side, facing forward toward the radiator. Best seen from underneath, just above the front subframe.
• 3.5L V6 (J35Y): Front-lower area of the engine, roughly centered, facing forward horizontally toward the radiator. Access is from below after removing the underpanel.
• Accord Hybrid (2.0L Atkinson): Front of the engine on the driver’s side, mounted low and often angled downward. Clearance is tight near the cooling fans, so undercar access is recommended.

If you’re under the car and looking up at the radiator side of the engine, the filter is a spin-on canister that sits just above the subframe area; its gasket seats against a machined pad on the block or an oil cooler base.

How to Access It Safely

Finding the filter is straightforward if you prepare the car correctly. The steps below describe a typical approach for all 2014 Accord variants.

1. Park on level ground, engage the parking brake, and let the engine cool. Gather tools and safety gear.
2. Lift the front of the vehicle with a jack and support it securely on jack stands at the factory pinch welds or subframe points. Never rely on the jack alone.
3. Remove the front engine under-cover (splash shield) by undoing the mix of 10 mm bolts and plastic push-pins/clips. Set fasteners aside in order.
4. From under the bumper area, look up at the radiator side of the engine block. Identify the round spin-on filter canister near the lower front of the engine (see engine-specific cues above).
5. Position an oil drain pan beneath the filter area before loosening the filter—some oil will spill as soon as the seal breaks free.

Once located, you can proceed with the oil change or inspection. Reinstall the under-cover securely, ensuring all fasteners and clips are returned to their original locations.

Visual Cues and Landmarks

If you’re having trouble spotting the filter, these nearby components can help you orient yourself under the car.

• Radiator and fans: The filter is on the engine side of these, facing toward them.
• Crank pulley/serpentine belt: The filter sits a bit above or beside this area on the radiator side of the block.
• Front subframe: Expect the filter to be just above or slightly behind the subframe crossmember.
• Half-shafts: On the I4, the filter is slightly toward the passenger side axle; on the Hybrid, more toward the driver side; on the V6, near center-front.

These landmarks remain consistent regardless of trim and help confirm you’re looking in the right place before you reach for tools.

Handy Specs, Tools, and Notes

While locating the filter, it’s helpful to know typical parts and specs used on this generation of Accord.

• Filter type: Honda spin-on canister. Common OEM part numbers include 15400-PLM-A01 or 15400-PLM-A02 (supersessions vary by region/dealer). Many quality aftermarket equivalents exist—match by year/engine.
• Filter wrench: 65/67 mm, 14-flute cap-style fits most Honda OEM filters; a strap wrench also works if space allows.
• Drain plug torque (for reference during an oil change): approximately 29 lbf·ft (39 N·m). Always use a new 14 mm aluminum crush washer.
• Filter tightening: Lightly oil the new gasket, spin on until the gasket contacts the base, then turn about 3/4 turn more by hand (or torque to spec if specified by the filter maker).
• Safety tip: Beware of hot exhaust and coolant components near the front of the engine if the car was recently running.

Confirm the exact filter part number and torque values in your owner’s manual or by VIN with a Honda parts source, especially if your car has had engine-related service or non-OEM parts installed.

Summary

On any 2014 Honda Accord, the oil filter is on the lower front (radiator side) of the engine and is most easily accessed from underneath after removing the splash shield. Four-cylinder models place it low and toward the passenger side facing forward; V6 models put it near the front-center facing forward; and Hybrids position it low on the driver’s side. Use proper lifting and safety practices, and consult your owner’s manual for any engine-specific details.

Where is the filter on a Honda Accord?

Down. And we’re going to shine a light up here to reveal. This cover. So now you should be able to see this cover that’s in place and behind this cover will be your cabin airflow filter.

How to change 2014 Honda Accord engine filter?

There’s three lift the box push forward pull the filter out match it up. Make sure it goes all the way. In little tabs here. And put the clips back in that’s it.

Where is the oil filter on a 2014 Honda Accord?

Sometime it’s tight. So there you go.

Where is your oil filter located?

In most vehicles, the oil filter is located on the engine block, near the oil pan. However, in others, the oil filter may be in a different location, such as above the engine, behind the radiator, or in the fender well. To find the exact location of your oil filter, you can refer to your car’s owner’s manual.