How Much Oil a 2019 Audi A4 2.0 T Takes

The 2019 Audi A4 2.0 T typically takes about 5.7 to 6.0 liters (approximately 6.0 to 6.3 US quarts) of engine oil with a filter change, depending on the specific 2.0 T engine variant and market. In more detail, Audi’s own documentation and service data indicate a capacity just under 6 liters for the common 2.0 TFSI engines used in the 2019 A4, meaning a standard 6‑quart oil change kit is generally appropriate, with the final level confirmed via the electronic oil measurement system.

Understanding the 2019 Audi A4 2.0 T Engine Variants

The 2019 Audi A4 2.0 T designation covers more than one engine configuration, and oil capacity can vary slightly between these. That makes it important to understand which exact engine code or power output your vehicle has before relying on a specific number.

Engine Codes and Power Outputs

Audi fitted several versions of the 2.0-liter turbocharged four-cylinder (TFSI) engine to the 2019 A4, and while they share the same basic architecture, service specifications can differ slightly by code, tune, and region.

This list outlines the most common 2.0 T engines found in the 2019 Audi A4 and what owners should know about them when checking oil capacity information.

• U.S. and Canada: Typically a 2.0 TFSI engine producing around 188–252 hp, commonly associated with engine codes like CYMC, CYRB, or similar, depending on exact trim and drivetrain (quattro vs. front-wheel drive).
• Europe and other markets: Multiple 2.0 TFSI variants with different power ratings, sometimes paired with mild-hybrid systems or different emission packages that can slightly alter service specs.
• “40 TFSI” or “45 TFSI” badges: Marketing labels that can map to different tunings of the same basic 2.0-liter engine, but do not change the general oil capacity range dramatically.

These variations mean that while most 2019 A4 2.0 T engines cluster around the same oil capacity, the safest approach is to cross-check your specific engine code or region-specific owner’s manual before performing a DIY oil change.

Exact Oil Capacity: What Audi Specifies

For everyday owners, the key figure is the refill capacity when changing both oil and filter. Audi’s service literature and widely used professional databases for the 2019 A4 2.0 TFSI generally specify an amount slightly under 6 liters, though you will often buy and use a 6‑quart kit.

Typical Oil Capacity Range

The following figures summarize the most common oil capacity specifications associated with the 2019 Audi A4 2.0 T when changing the oil and filter.

This list summarizes the typical capacity numbers you’ll encounter in manuals, service data, and parts catalogs for this model year and engine type.

• Approximate capacity with filter: 5.7 to 6.0 liters (about 6.0 to 6.3 US quarts).
• Common U.S. service practice: Use a 6‑quart oil change kit, then confirm and fine-tune the level after the engine has circulated the oil.
• Some data sources list: Around 5.8 liters (about 6.1 quarts) as the nominal refill amount for the 2.0 TFSI.
• Without filter change: Capacity can be slightly lower, as some old oil remains in the system.

In practical terms, this means that a 6‑quart supply usually covers a full change with a small margin, but you should avoid simply dumping in the entire amount without checking the electronic level reading afterward.

Checking Your Specific Model’s Requirement

Because Audi uses electronic oil level measurement on many 2019 A4 models and offers different trims globally, confirming your exact requirement is a matter of verifying a few key details about your car and then cross-referencing the official documentation.

Where to Find the Official Capacity

Confirming the correct oil volume for your exact 2019 A4 2.0 T is straightforward if you know where to look. These sources provide the most reliable and current information.

This list explains the primary places owners can check to verify the precise oil capacity specified for their individual vehicle.

1. Owner’s manual: Look under sections like “Capacities,” “Engine oil,” or “Technical data” for the engine oil refill quantity with filter.
2. Service manual or dealership printout: Audi dealers can access up-to-date factory service information by VIN, including the official oil capacity.
3. Under-hood labels or service stickers: Some markets include a sticker or label with oil specification and sometimes a capacity note.
4. VIN-based online parts catalogs: Reputable Audi/VAG parts sites can show the engine code and often list nominal oil volume for that engine.

Using one or more of these references ensures that small regional differences or running production changes are accounted for before you add oil.

What Type of Oil Does the 2019 A4 2.0 T Use?

Knowing how much oil to add is only part of the task; the 2019 Audi A4 2.0 T also requires oil that meets specific VW/Audi standards to protect its turbocharged, direct-injection engine and maintain warranty compliance.

Recommended Oil Specifications

Audi specifies oil by an internal Volkswagen Group standard, rather than just viscosity. Using oil that meets these standards is more important than brand alone.

This list highlights the key oil specifications and characteristics Audi typically requires for the 2019 A4 2.0 T engine.

• VW 502 00 / 504 00: Common specifications for gasoline Audi engines of this era; your manual will state which is required or permitted.
• Viscosity: Often 0W‑20, 0W‑30, or 5W‑40 depending on market, climate, and specific engine; the manual or filler cap usually indicates the preferred grade.
• Fully synthetic: High-quality full-synthetic oil is standard and recommended for proper turbocharger and cold-start protection.
• Approved brands: Many major oil manufacturers produce VW 502.00/504.00-approved oils; look for the approval on the bottle, not just “meets requirements.”

By matching both the VW specification and the recommended viscosity for your climate, you ensure the engine receives the level of protection Audi engineered for.

How to Perform an Oil Change on a 2019 A4 2.0 T Safely

For owners tackling a DIY oil change, the most important steps involve safely lifting the car, draining the oil completely, replacing the filter, and then refilling carefully while checking the electronic oil system readout.

Basic Oil Change Steps

The following steps give a high-level view of the oil change process on the 2019 Audi A4 2.0 T, focusing on capacity control and verification rather than every mechanical detail.

This list breaks down the oil change workflow so that owners understand why capacity is added gradually and checked electronically rather than assumed.

1. Warm the engine: Run the car briefly so the oil flows more freely, but avoid working on a very hot engine.
2. Raise and secure the vehicle: Use proper jack points and jack stands or a lift; remove the underbody shield if fitted.
3. Drain the oil: Remove the drain plug and allow the oil to fully drain from the sump; replace the plug with a new washer if specified.
4. Replace the oil filter: Swap in a new filter of the correct part number, lubricating the gasket and tightening to spec.
5. Add initial oil amount: Pour in slightly less than the maximum expected capacity (for example, around 5.5 liters/5.8 quarts).
6. Run and recheck: Start the engine for a short period, then shut it off and wait a few minutes so oil can settle.
7. Use electronic oil level check: Via the MMI or instrument cluster, check the oil level and top off gradually until it reaches the proper range.

This staged approach avoids overfilling, which can harm seals, cause foaming, and lead to other operating issues in a turbocharged engine like the A4’s.

Why Not Simply Fill to a Fixed Number?

Owners often search for a precise capacity figure and expect to pour that amount in one step, but modern engines and electronic dipstick systems make it better practice to treat the published capacity as a guideline rather than a rigid rule.

The Role of Tolerances and Residual Oil

Several real-world factors explain why Audi’s published oil capacity for the 2019 A4 2.0 T is best viewed as approximate rather than absolute.

This list details the key reasons that the nominal capacity can differ slightly from what you actually pour in during any specific oil change.

• Residual oil: Some oil always remains in passages, the turbocharger, and other engine areas, so a completely “dry” fill capacity is rarely reached.
• Filter and component variation: Different oil filters and minor component differences can change the precise volume held in the system.
• Temperature effects: Oil expands and contracts with temperature, affecting measured level even if the actual volume is unchanged.
• Measurement method: The electronic oil level system has its own calibration limits and requires specific conditions (flat ground, engine at operating temp, short wait after shutoff) for accurate readings.

By treating 5.7–6.0 liters as a working range and relying on the in-car level gauge for final verification, owners ensure the engine is neither overfilled nor underfilled despite these variations.

Summary

The 2019 Audi A4 2.0 T generally requires just under 6 liters—around 5.7 to 6.0 liters, or roughly 6.0 to 6.3 US quarts—of engine oil when changing both oil and filter, though the exact figure can vary slightly by specific 2.0 TFSI engine variant and market. Audi specifies fully synthetic oil that meets VW standards such as 502.00 or 504.00, in a viscosity like 0W‑20, 0W‑30, or 5W‑40 depending on region and climate. The most reliable method is to add slightly less than the published capacity, run the engine briefly, then top off gradually while using the A4’s electronic oil-level display to confirm the final level. Checking the owner’s manual or dealer service data by VIN ensures that your particular 2019 A4 2.0 T receives the correct quantity and specification of oil.

What oil does the Audi A4 2019 take?

The 2019 Audi A4 typically requires a full synthetic 0W-30 or 5W-40 engine oil that meets the VW 504.00 (or the older VW 502.00) Audi/VW oil specification. Always confirm the exact requirement for your specific engine, as different versions of the 2.0T engine may have different specifications, notes eEuroparts.com. 
Key details

• Oil type: Full synthetic is recommended for optimal performance. 
• Viscosity: Check your owner’s manual for the specific viscosity for your engine. Common options are 0W-30 or 5W-40. 
• Specification: The oil must meet the Audi/VW specification. For the 2.0T engine, this is likely VW 504.00 or VW 502.00. 
• Recommendation: It is highly recommended to use an oil change kit designed for your specific vehicle, as it will contain the correct oil, filter, and other necessary parts. 
• Caution: Always verify the correct oil specification in your vehicle’s owner’s manual before purchasing to ensure proper engine protection, especially if the car is still under warranty, notes this YouTube video. 

How much oil does a 2.0 4 cylinder engine take?

Approximately 5.1 quarts
2.0L turbocharged engine: Approximately 5.1 quarts of oil.

How much oil does a 2019 Audi A4 2.0 TFSI take?

Capacity: 5.5 quarts (with filter).

How much oil does a Audi A4 2.0 T take?

The Audi A4 2.0T oil capacity is typically between 4.5 and 5.5 quarts, with many models requiring around 5.5 quarts with a filter change. However, the exact capacity varies by model year, so it is crucial to consult your specific owner’s manual or check the vehicle’s onboard oil level system to ensure you add the correct amount. 
Oil capacity by model year (approximate)

• 2017-Present: Approximately 5.5 quarts
• 2009-2016: Around 5 quarts
• 2006-2013: Between 4.5 and 4.9 quarts 

Important considerations

• Always verify: The most accurate capacity for your specific vehicle can be found in your owner’s manual or by using the digital oil level check in the car’s MMI system. 
• Check after filling: After adding oil, start the engine and let it run for a minute to circulate the oil. Then, turn it off and check the level again to ensure it is within the correct range. 
• Oil type: Use a synthetic oil that meets the correct Audi/Volkswagen oil quality standard (e.g., VW 502 00) and viscosity grade for your climate.